Panasonic VariCam LT Operating Manual page 159

Item
[FRAME SIG]
[FRAME COLOR]
[FRAME LEVEL]
[USER BOX]
[USER BOX WIDTH]
[USER BOX HEIGHT]
[USER BOX H POS]
[USER BOX V POS]
[VF SDI FOCUS [EXPAND MODE]
ASSIST]
[EXPAND1 SW]
[- POS1]
[- VALUE1]
[EXPAND2 SW]
[- POS2]
[- VALUE2]
[FOCUS IN COLOR SW] Displays/hides the peaking function.
[- PEAKING VALUE]
[- COLOR SEL]
[- MONO]
[FOCUS SQUARES SW] Displays/hides the focus square function.
[MONO SW]
[FOCUS DISP]
Chapter 10 Menu Operations — Menu list
Sets frame marker aspect ratio.
[1.33:1], [1.44:1], [1.56:1], [1.78:1], [1.85:1], [2.00:1], [2.201:1], [2.35:1], [2.39:1]
f Factory setting: [2.39:1]
Sets the color of the frame marker.
[WHITE], [BLACK], [RED], [GREEN], [BLUE], [YELLOW]
f Factory setting: [WHITE]
Sets the level of the outside of the frame marker.
[0%] - [100%] (10% step)
f Factory setting: [100%]
Switches enable/disable of the user box display.
[ON], [OFF]
f Factory setting: [OFF]
Sets the width of the user box.
[1] - [100]
f Factory setting: [13]
Sets the height of the user box.
[1] - [100]
f Factory setting: [13]
Sets the horizontal position of the center of the user box.
[−50] - [50]
f Factory setting: [0]
Sets the vertical position of the center of the user box.
[−50] - [50]
f Factory setting: [0]
Sets the enlargement display function mode.
[10SEC]: Disables the enlarged display function after ten seconds have elapsed.
[HOLD]: Enables the enlarged display function.
[UNTIL REC]: Enables the enlarged display function until performing recording operation.
f Factory setting: [10SEC]
Switches display/hide of the enlargement display function 1.
[ON], [OFF]
f Factory setting: [OFF]
Adjusts the source signal position in an enlarged display.
[0] - [8]
f Factory setting: [4]
Adjusts the enlargement factor.
[x2], [x3], [x4]
f Factory setting: [x2]
Switches display/hide of the enlargement display function 2.
[ON], [OFF]
f Factory setting: [OFF]
Adjusts the source signal position in an enlarged display.
[0] - [8]
f Factory setting: [4]
Adjusts the enlargement factor.
[x2], [x3], [x4]
f Factory setting: [x2]
[ON], [OFF]
f Factory setting: [OFF]
Sets the peaking function mode.
[LOW], [MID], [HIGH]
f Factory setting: [MID]
Sets the peaking function color.
[RED], [GREEN], [WHITE]
f Factory setting: [RED]
Switches enable/disable of the monochrome display function when the peaking function is displayed.
[ON], [OFF]
Even if it is set to [OFF], background image is displayed in monochrome when [MONO SW] is set to [ON].
If it is set to [ON], background image is displayed in monochrome even when [MONO SW] is set to [OFF].
f Factory setting: [OFF]
[ON], [OFF]
f Factory setting: [OFF]
Switches enable/disable of monochrome display function.
[ON], [OFF]
Even if it is set to [OFF], background image is displayed in monochrome when [- MONO] is set to [ON].
If it is set to [ON], background image is displayed in monochrome even when [- MONO] is set to [OFF].
f Factory setting: [OFF]
Sets the unit for the focus distance display.
[Meter], [Feet]
f Factory setting: [Feet]
– 159 –
Description of settings