[Output Settings] - Panasonic VariCam LT Operating Manual

[OUTPUT SETTINGS]

Sets the display contents of the output video and output from the <SDI OUT 1>/<SDI OUT 2>/<VF SDI> terminal.
Item
[SDI OUT] [RAW OUTPUT]
[SDI REC REMOTE]
[SDI OUT FORMAT]
[3G-SDI OUT]
[SDI OUT 2 SIGNAL
SEL]
[SDI OUT 1 CLEAN
VIEW]
[SDI OUT 2 CLEAN
VIEW]
[MENU DISP]
[PLAY DISP & CTRL]
[PROCESSED RAW
SW]
Chapter 10 Menu Operations — Menu list
Sets if the RAW output from the <SDI OUT 1>/<SDI OUT 2> terminal will be dual output (DUAL) or single
output (SINGLE).
[DUAL], [SINGLE]
f Factory setting: [DUAL]
It can be set to [SINGLE] only when the following three conditions are fulfilled. It will be fixed to [DUAL] for
all other cases.
f When [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [FREQUENCY] is set to [29.97p] or
lower
f When [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [SDI RAW] is set to [4K/10bit] or
[UHD/10bit]
f When [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [MAIN CODEC] is set to [AVC-Intra4K
422]
Sets if the recording operation control function against the external device (such as recorder) connected to
the <SDI OUT 1>/<SDI OUT 2> terminal is used or not.
It can be output from the <SDI OUT 2> terminal only when [SDI OUT2 SIGNAL SEL] is set to [SDI OUT 1].
The recording operation can be controlled only when the camera is recording.
[ON]: Controls the recording operation of the external device.
[OFF]: Does not control the recording operation of the external device.
f Factory setting: [OFF]
Selects the signal to be output from the <SDI OUT 1>/<SDI OUT 2> terminal.
It is output in the HD (1920×1080) format letterbox regardless of the [MAIN PIXEL] setting.
Item that can be selected depends on the [FREQUENCY] setting. This can be selected only when
[FREQUENCY] is set to [50.00p] or [59.94p].
When [FREQUENCY] is set to [23.98p]: [23.98PsF]
When [FREQUENCY] is set to [24.00p]: [24.00PsF]
When [FREQUENCY] is set to [25.00p]: [25.00PsF]
When [FREQUENCY] is set to [29.97p]: [29.97PsF]
When [FREQUENCY] is set to [50.00p]: [50.00p]/[50.00i]
When [FREQUENCY] is set to [59.94p]: [59.94p]/[59.94i]
When [FREQUENCY] is set to [50.00i]: [50.00i]
When [FREQUENCY] is set to [59.94i]: [59.94i]
f Factory setting: [23.98PsF]
Sets the format for the 3G-SDI signal output from the <SDI OUT 1>/<SDI OUT 2> terminal.
[LEVEL-A]: Selects the LEVEL-A method.
[LEVEL-B]: Selects the LEVEL-B DL method.
f Factory setting: [LEVEL-B]
Sets the output from the <SDI OUT 2> terminal.
[SDI OUT 1]: Same output as the <SDI OUT 1> terminal.
[VF SDI]: Same output as the <VF SDI> terminal.
f Factory setting: [SDI OUT 1]
Sets if the output from the <SDI OUT 1> terminal will be video only or to superimpose the signal for marker
or indicator.
[ON]: Outputs video only.
[OFF]: Outputs the signals for video and marker or indicator.
f Factory setting: [OFF]
Sets if the output from the <SDI OUT 2> terminal will be video only or to superimpose the signal for marker
or indicator.
[ON]: Outputs video only.
[OFF]: Outputs the signals for video and marker or indicator.
f Factory setting: [OFF]
Sets if the menu is displayed in the output from the <SDI OUT 1>/<SDI OUT 2> terminal.
[ON], [OFF]
f Factory setting: [OFF]
Sets if the PLAY screen is displayed in the output from the <SDI OUT 1>/<SDI OUT 2> terminal, and
playback control is performed or not with the remote operation panel AK-HRP200G.
[ON], [OFF]
f Factory setting: [OFF]
Sets if the information with the shading adjusted is to be added to the RAW signal or not.
[OFF], [ON]
f Factory setting: [OFF]
– 154 –
Description of settings