Mitsubishi Electric 800 Series Instruction Manual page 80

Pr. group Pr.
C203 51 Rated second motor current
C204 456 Rated second motor voltage
C205 457 Rated second motor frequency
Second motor maximum
C206 743
frequency
C207 744 Second motor inertia (integer)
Second motor inertia
C208 745
(exponent)
Second motor auto tuning
C210 463
setting/status
Second motor online auto
C211 574
tuning
C220 458 Second motor constant (R1)
C221 459 Second motor constant (R2)
Second motor constant (L1) /
C222 460
d-axis inductance (Ld)
Second motor constant (L2) /
C223 461
q-axis inductance (Lq)
C224 462 Second motor constant (X)
Second motor excitation
C225 455
current
Second motor torque current/
C226 860
Rated PM motor current
Second motor induced voltage
C230 738
constant (phi f)
C231 739 Second motor Ld decay ratio
C232 740 Second motor Lq decay ratio
Second motor protection
C233 746
current level
Second motor induced voltage
C235 1413
constant (phi f) exponent
Second motor starting
C282 741 resistance tuning
compensation coefficient 1
Second motor magnetic pole
C285 742
detection pulse width
Starting resistance tuning
C288 737
compensation coefficient 2
 A: Application parameters
Parameters for the setting of a specific application.
Pr. group Pr.
A100 278 Brake opening frequency
A101 279 Brake opening current
Brake opening current
A102 280
detection time
A103 281 Brake operation time at start
A104 282 Brake operation frequency
A105 283 Brake operation time at stop
Brake opening current
A108 639
selection
Brake operation frequency
A109 640
selection
Refer
Name
to page
198,
299,
308
299,
308
299,
308
308
308
308
299,
308,
358
315
299,
308,
358
299
299,
308
299,
308
299
299
299,
308
308
308
308
308
308
308
308
308
Refer
Name
to page
320
320
320
320
320
320
320
320
Pr. group Pr.
Automatic acceleration/
A110 292
deceleration
Stop-on-contact control
A200 270
selection
Stop-on contact excitation
A205 275 current low-speed scaling
factor
PWM carrier frequency at stop-
A206 276
on contact
A300 592 Traverse function selection
A301 593 Maximum amplitude amount
Amplitude compensation
A302 594
amount during deceleration
Amplitude compensation
A303 595
amount during acceleration
A304 596 Amplitude acceleration time
A305 597 Amplitude deceleration time
Parameter for manufacturer setting. Do not
A600 759
set.
A601 131 PID upper limit
A602 132 PID lower limit
A603 553 PID deviation limit
A604 554 PID signal operation selection
Integral stop selection at
A607 1015
limited frequency
A610 128 PID action selection
A611 133 PID action set point
PID control automatic
A612 127
switchover frequency
A613 129 PID proportional band
A614 130 PID integral time
A615 134 PID differential time
Output interruption detection
A621 575
time
Output interruption detection
A622 576
level
Output interruption cancel
A623 577
level
PID set point/deviation input
A624 609
selection
PID measured value input
A625 610
selection
A630 C42 PID display bias coefficient
A631 C43 PID display bias analog value
A632 C44 PID display gain coefficient
A633 C45 PID display gain analog value
Automatic restart after
A700 162 instantaneous power failure
selection
Rotation direction detection
A701 299
selection at restarting
A702 57 Restart coasting time
A703 58 Restart cushion time
Stall prevention operation
A710 165
level for restart
3.3 Parameter list (by function group number)
Refer
Name
to page
171,
320
324
324
324
327
327
327
327
327
327
329,
344
329,
344
329
329
329
329,
344
329,
344
329
329,
344
329,
344
329,
344
329
329
329
329,
344
329,
344
342
342
342
342
351,
356,
358
351
351,
356
351
351
79
3. Parameters
1
2
3
4
5
6
7
8
9
10