Mitsubishi Electric 800 Series Instruction Manual (Function page 370

○: Assignment/input available, ─: Assignment/input unavailable (no function)
*1 The communication protocol affects which terminals can be used. For details, refer to the Instruction Manual (Communication) or the Instruction
Manual of each communication option.
 Input signal list
• Refer to the following table and set the parameters.
Signal
Setting
name
Pr.59 = "0" (initial value)
0 RL
Pr.59 ≠ "0"
Pr.270 = "1, 11"
Pr.59 = "0" (initial value)
1 RM
Pr.59 ≠ "0"
Pr.59 = "0" (initial value)
2 RH
Pr.59 ≠ "0"
Second function selection
3 RT
Pr.270 = "1, 11"
4 AU Terminal 4 input selection
5 JOG Jog operation selection
7 OH
External thermal relay input
15-speed selection (Combination with multi-speeds of RL, RM, and
8 REX
RH)
10 X10 Inverter run enable (FR-XC/FR-HC2/FR-CV connection)
12 X12 PU operation external interlock
13 X13 External DC injection brake operation start
14 X14 PID control valid
15 BRI Brake opening completion
16 X16 PU/External operation switchover (External operation with X16-ON) Pr.79, Pr.340
18 X18 V/F switchover (V/F control with X18-ON)
23 LX Pre-excitation/servo ON
24 MRS Output stop
STP
25 Start self-holding selection
(STOP)
26 MC Control mode switchover
27 TL Torque limit selection
30 JOG2
37 X37 Traverse function selection
42 X42 Torque bias selection 1
43 X43 Torque bias selection 2
46 TRG Trace trigger input
47 TRC Trace sampling start/end
50 SQ Sequence start
51 X51
Fault clear
Forward rotation command (assignable to the STF terminal
60 STF
(Pr.178) only)
Reverse rotation command (assignable to the STR terminal
61 STR
(Pr.179) only)
62 RES Inverter reset
65 X65 PU/NET operation switchover (PU operation with X65-ON)
66 X66 External/NET operation switchover (NET operation with X66-ON)
Command source switchover (command by Pr.338 or Pr.339
67 X67
enabled with X67-ON)
72 X72 PID P control switchover
74 X74 Magnetic flux decay output shutoff
Function
Low-speed operation command
*1
Remote setting (setting clear)
*2
Stop-on-contact selection 0
Middle-speed operation
command
*1
Remote setting (deceleration)
High-speed operation command
*1
Remote setting (acceleration)
*2
Stop-on-contact selection 1
*3
Related parameter
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.59
Pr.270, Pr.275, Pr.276
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.59
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.59
Pr.44 to Pr.48, Pr.51, Pr.450
to Pr.463, Pr.569, Pr.832,
Pr.836, etc.
Pr.270, Pr.275, Pr.276
Pr.267
Pr.15, Pr.16
Pr.9
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.17, Pr.30, Pr.70
Pr.79
Pr.10 to Pr.12
Pr.127 to Pr.134, Pr.575 to
Pr.577
Pr.278 to Pr.285
Pr.80, Pr.81, Pr.800
Pr.850
Pr.17
Pr.250
Pr.800
Pr.815
Pr.15, Pr.16
Pr.592 to Pr.597
Pr.840 to Pr.845
Pr.840 to Pr.845
Pr.1020 to Pr.1047
Pr.1020 to Pr.1047
Pr.414
Pr.414
Pr.250
Pr.250
Pr.75
Pr.79, Pr.340
Pr.79, Pr.340
Pr.338, Pr.339
Pr.127 to Pr.134, Pr.575 to
Pr.577
Pr.850
14. (T) Multi-Function Input Terminal Parameters
14.6 Input terminal function selection
11
12
Refer to
page
13
273
240
415
14
273
240
15
273
240
16
374
415
350
17
271
276
273
18
484
250
476
19
420
410
250
20
104
476
372
376
104
122
271
418
133
133
459
459
457
*4
376
376
197
250
250
261
420
476
369