Mitsubishi Electric MELSEC iQ-R Series User Manual page 228

Error Error definition and causes
code
D612H Parameter error (each station device range
assignment error (RWw))
D613H Parameter error (each station device range
assignment error (RWr))
D614H Parameter error (each station device range
assignment error (RWr))
D615H Parameter error (each station device range
assignment error (RY))
D616H Parameter error (each station device range
assignment error (RY))
D617H Parameter error (each station device range
assignment error (RX))
D618H Parameter error (each station device range
assignment error (RX))
D619H Parameter error
D61AH Parameter error
D61BH Parameter error (device overlap error
(RWw))
D61CH Parameter error (device overlap error (RWr))
D61DH Parameter error (device overlap error (RY))
D61EH Parameter error (device overlap error (RX))
4 TROUBLESHOOTING
226
4.5 List of Error Codes
Action
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset of the link device
of the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the size of the link device of
the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset of the link device
of the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the size of the link device of
the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset of the link device
of the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the size of the link device of
the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset of the link device
of the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset or size of the link
device of the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset or size of the link
device of the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset or size of the link
device of the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset or size of the link
device of the slave station in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
Detailed
information 1
Detailed
information 2












