Sony SRW-5001 Operation Manual page 49

2
Press the [F2] (MEMORY CARD) button.
The MEMORY CARD menu appears in the
display.
F O R M A T
C A R D B A N K 0
C A R D
( B A S E B A L L )
( P r e s e t )
U N D O
( P r e s e t )
( P r e s e t )
( P r e s e t )
S H O W
( P r e s e t )
S E T U P
( P r e s e t )
( P r e s e t )
S H O W
( P r e s e t )
C U E S E T
E D I T S E L E C T D I R E C -
T I T L E A L L T I O N
3
Press the [F8] (DIRECTION) button to select the
, direction.
The left cursor bar flashes.
4
Move the cursor (B) to the memory stick side
using the cursor T button and use the cursor R or
r buttons to place the cursor bar by the memory
bank where the settings were saved.
F O R M A T
C A R D B A N K 0
C A R D
Destination ( B A S E B A L L )
( P r e s e t )
U N D O
( P r e s e t )
( P r e s e t )
( P r e s e t )
S H O W
( P r e s e t )
S E T U P
( P r e s e t )
( P r e s e t )
S H O W
( P r e s e t )
C U E S E T
E D I T
T I T L E
5
To change the title of the memory bank, press the
[F6] (EDIT TITLE) button.
The title can also be changed after the settings are
recalled.
For details, see"4-1-6 Adding Titles to the Data"on
page 4-11.
6
Press the cursor t button to move the cursor (B)
to the VTR side, then press the cursor R or r button
to move the cursor to the VTR memory bank
number where the recalled data are to be stored.
C U R R E N T C U E S E T
0 C F O O T B A L L
1 F ( P r e s e t )
2
3
4
5
6
7
8
C O P Y E X I T
C U R R E N T C U E S E T
0 C F O O T B A L L
1 F ( P r e s e t )
2
3
4
5
6
7
8
S E L E C T D I R E C - C O P Y E X I T
A L L T I O N
F O R M A T
C A R D B A N K 0
C A R D
( B A S E B A L L ) 0
( P r e s e t ) 1
U N D O
( P r e s e t ) 2
( P r e s e t ) 3
( P r e s e t ) 4
S H O W
( P r e s e t ) 5
S E T U P
( P r e s e t ) 6
( P r e s e t ) 7
S H O W
( P r e s e t ) 8
C U E S E T
E D I T S E L E C T D I R E C - C O P Y
T I T L E A L L T I O N
To change the current VTR menu settings
Move the cursor (B) to [C] (CURRENT SETUP).
To replace all VTR memory bank contents with
memory stick data
Press the [F7] (SELECT ALL) button.
Note
If there are protected items at the destination end, it
is not possible to select the [F7] (SELECT ALL)
button.
7
Press the [F9] (COPY) button.
A message asking you to confirm the operation
appears in the display.
8
Press the [F9] (COPY) button while holding down
the SFT button.
The VTR recalls the contents of the memory stick.
After the recalling process is complete, the title of
the memory bank of the memory stick appears
under the VTR indication.
9
Press the [F10] (EXIT) button.
The SET UP menu appears again.
C U R R E N T C U E S E T
Destination
C F O O T B A L L
F ( P r e s e t )
(flashing)
E X I T
4-9
Chapter 4 Menu Settings