Table of Contents
Advertisement
4-4 CUE Menu
To delete a time code
1
Use the cursor buttons to move the cursor to the
Time section to be deleted.
To move the cursor using the numeric buttons
Enter the line number using the numeric buttons.
Then press the [F9] (CUENUM POINT) button.
The cursor will move to the line specified by the
numeric buttons.
2
Press the [F5] (DEL POINT) button.
A message appears (in the control panel display)
requesting confirmation of the deletion operation.
3
Then, press the [F5] (DEL POINT) button while
pressing down the SFT button.
The time code section becomes blank and is ready
for new time data input.
To delete the line as well as the time code
Use the cursor buttons to move the cursor to the
time code to be deleted.
Then press the [F5] (DEL POINT) button while
pressing down the SFT button, the line is deleted
and all the line numbers below are decreased by
one.
C U E
R E C D A T E [ 2 0 0 3 / 0 2 / 2 5 ]
S C A N
T I T L E [ S O N Y
!
D e l e t e C u e P o i n t :
N o . I N
E N T R Y
P O I N T
0 0 0 : 0 0 : 0 4 : 0 5
C U E
1 0 0 : 0 3 : 4 5 : 2 1 0 1 : 0 0 : 3 6 : 0 6 5 9 i 1 0 8 0
C O M M N T
2 0 1 : 0 4 : 2 7 : 2 3 0 1 : 0 5 : 3 1 : 2 4 5 9 i 1 0 8 0
E D I T
P r e s s [ S F T ] + [ F 5 ] t o D E L E T E .
3 - - : - - : - - : - - - - : - - : - - : - - - - - - - - -
P r e s s o n l y [ C L R ] t o C A N C E L .
C H A N G E
D A T A
D E L
M A R K
P R O -
P O I N T
T E C T
To undo the deletion of a time data or line
Press the ALT/[F2] (UNDO ALL) buttons.
A message appears (in the control panel display)
requesting confirmation of the undo operation.
Press the [F2] (UNDO ALL) button while pressing
down the SFT button. To cancel the undo
operation, press the CLR button.
4-48
Chapter 4 Menu Settings
E O S [ - - : - - : - - : - - ]
] R e s t 8 5 %
O U T
T a p e F o r m a t
0 0 : 0 0 : 0 9 : 2 3 5 9 i 1 0 8 0
T A P E
C U E N U M
W R I T E /
I N F O
P O I N T
E X I T
To copy time data of a cue point to another
cue point specified in the CUE menu
1
Press the ALT/[F4] (COPY to CUE) buttons.
A message appears (in the control panel display)
requesting confirmation of the copy operation.
To cancel the copy operation
Press the CLR button.
2
Press the [F4] (COPY to CUE) button while
pressing down the SFT button.
The time data of the cue point is copied to the cue
point indicated in the CUE menu.
Changing Mrk data
Use the cursor buttons to move the cursor to the line
with the mark attribute to be changed, and then press
the [F6] (MARK) button. Or, move the cursor directly
to the mark attribute to be changed, and then press the
[F4] (CHANGE DATA) button. In both cases, each
press of the button changes the attribute as follows:
OK t NG tKP (keep temporarily) t blank (no
attribute).
Changing the recording starting point setting
Use the cursor buttons to move the cursor to the
recording starting point section. Then press the [F4]
(CHANGE DATA) button. Each press of the button
turns the setting "on" (the @ indication appears) or
"off" (the indication disappears).
Entering and modifying IN/OUT point data
You can use either the ENTRY button or the numeric
buttons to enter and modify IN/OUT point data.
Advertisement
Table of Contents
