Table of Contents
Advertisement
Keychain TP PTN (0006)
Controls which partitions the selected keychain touchpad can arm/disarm.
When enabled, the selected keychain touchpad can arm/disarm the parti-
tions selected in this menu. When disabled, the selected keychain touchpad
cannot arm/disarm multiple partitions.
•
If no keychain touchpads are learned into panel memory, this menu
displays NOT AVAILABLE.
•
When keychain touchpads are learned into panel memory, two sub-
menus appear. The first one lets you view keychain touchpad assign-
ments similar to that of viewing learned sensors (sensor #, partition
learned into, sensor group, etc.). The second sub-menu lets you view
and change the multi-partition arming assignments for that keychain
touchpad.
•
At least two partitions must be selected for this feature to work.
•
Keychain touchpads can arm/disarm multiple partitions only for those
partitions set up in the MULTI-PARTITION ARM/DISARM menu.
•
A partition cannot be armed/disarmed if it is being controlled by
another source at that time.
•
When arming multiple partitions from a keychain touchpad (press and
release Lock button), any conditions that prevent arming (open sen-
sor, trouble, active alarm, etc.) are identified on touchpad displays in
the partition where that condition exists. Touchpad displays in all
other partitions being armed display PROTEST. The normal protest/
auto force arm sequence follows, or pressing * on any touchpad in a
partition being armed cancels the arming request. Pressing the Lock
button again during a protest bypasses any open sensors in the
affected partitions and arms those partitions.
•
When disarming multiple partitions with a keychain touchpad and
alarms are active in one or more of the assigned partitions:
a). Protest beeps sound for five minutes in all partitions being dis-
armed; b). Partitions in alarm where sirens have timed out sound pro-
test beeps for five minutes; c). Partitions in alarm with active sirens
continue sounding the alarm.
In any case where alarms are active the premises may not be safe to
enter. The user has these options: 1). Leave and call for help from a
safe location; 2). If entering the premises anyway, go to a hardwired
touchpad and check the system status to determine the alarm. Disarm
and alarm memory is displayed for all assigned partitions; 3). Press
the keychain touchpad Unlock button a second time (within the five
minute protest period) to disarm all assigned partitions and cancel all
alarms, then go to a hardwire touchpad and check alarm memory.
Account Number (0010 - 0060)
The account number is used as panel (or customer) identification for the cen-
tral monitoring station. The panel sends the account number every time it
reports to the central station. Account numbers must be 1 to 10 characters
long.
Alpha characters A–F can be assigned to the account number by pressing
and holding buttons 1–6 respectively, until the character appears.
Note
When using the CID reporting format, the letter "A" is reported as a "0".
29
The following sections describe the Security settings that appear under
WWW.DIYALARMFORUM.COM
Security-Global (Default = keychain TP parti-
To enable Keychain TP PTN:
1. Learn all keychain touchpads into panel
memory (see
LEARN SENSORS
2.
Enter this menu (display showing
), then press #. The display shows the
TP PTN
lowest touchpad sensor number assignment
such as:
where S1 is sensor 1, P1 is
S1 P1 G0 TP RF
partition 1, G0 is sensor group 0, TP is
touchpad and RF is wireless.
3. Press # to accept this keychain touchpad or
press A or B until the desired keychain touch-
pad appears, then press #. The display shows
.
ARM PARTITION
4.
Enter the desired partitions 1-6 (at least
two). The display flashes the entered parti-
tions.
5.
Press # and the display stops flashing.
To disable Keychain TP PTN:
1. Follow steps 2 and 3 above.
2. Enter the partition numbers that are displayed
(except for the partition you assigned the
touchpad when it was learned). Each will dis-
appear from the display with the touchpad's
original partition number left flashing.
3.
Press # and the display stops flashing.
PARTITION 1
Security-Partition 1-6 (Default = 00000)
To program an Account Number:
1.
With the display showing
(current number), enter the
BER nnnnn
desired account number. The display
flashes the entered number.
2.
Press # and the display shows the new
number.
Concord 4 Series Systems
tion assignment)
menu)
.
KEYCHAIN
-
.
6
ACCOUNT NUM-
Hide quick links:
Advertisement
Table of Contents
