Siemens SINUMERIK 840D sl Operating Manual page 13
Milling
Hide thumbs
Also See for SINUMERIK 840D sl:
- Function manual (2184 pages) ,
- Programming manual (1334 pages) ,
- Commissioning manual (1102 pages)
Table of Contents
Advertisement
9.18.2
Programming........................................................................................................................304
9.18.3
Results/simulation test.........................................................................................................315
9.18.4
G code machining program..................................................................................................317
10
Programming technological functions (cycles).........................................................................................321
10.1
Drilling..................................................................................................................................321
10.1.1
General................................................................................................................................321
10.1.2
Centering (CYCLE81)..........................................................................................................322
10.1.3
Drilling (CYCLE82)...............................................................................................................324
10.1.4
Reaming (CYCLE85)...........................................................................................................327
10.1.5
Deep-hole drilling 1 (CYCLE83)...........................................................................................329
10.1.6
Deep-hole drilling 2 (CYCLE830).........................................................................................333
10.1.7
Boring (CYCLE86)...............................................................................................................343
10.1.8
Tapping (CYCLE84, 840).....................................................................................................345
10.1.9
Drill and thread milling (CYCLE78)......................................................................................352
10.1.10
Positioning and position patterns.........................................................................................356
10.1.11
Arbitrary positions (CYCLE802)...........................................................................................357
10.1.12
Row position pattern (HOLES1)...........................................................................................361
10.1.13
Grid or frame position pattern (CYCLE801).........................................................................362
10.1.14
Circle or pitch circle position pattern (HOLES2)...................................................................364
10.1.15
Displaying and hiding positions............................................................................................367
10.1.16
Repeating positions..............................................................................................................368
10.2
Milling...................................................................................................................................369
10.2.1
Face milling (CYCLE61).......................................................................................................369
10.2.2
Rectangular pocket (POCKET3)..........................................................................................372
10.2.3
Circular pocket (POCKET4).................................................................................................378
10.2.4
Rectangular spigot (CYCLE76)............................................................................................385
10.2.5
Circular spigot (CYCLE77)...................................................................................................390
10.2.6
Multi-edge (CYCLE79).........................................................................................................394
10.2.7
Longitudinal groove (SLOT1)...............................................................................................398
10.2.8
Circumferential groove (SLOT2)..........................................................................................404
10.2.9
Open groove (CYCLE899)...................................................................................................410
10.2.10
Long hole (LONGHOLE) - only for G code programs..........................................................418
10.2.11
Thread milling (CYCLE70)...................................................................................................420
10.2.12
Engraving (CYCLE60)..........................................................................................................424
10.3
Contour milling.....................................................................................................................429
10.3.1
General................................................................................................................................429
10.3.2
Representation of the contour..............................................................................................429
10.3.3
Creating a new contour........................................................................................................431
10.3.4
Creating contour elements...................................................................................................433
10.3.5
Changing the contour...........................................................................................................437
10.3.6
Contour call (CYCLE62) - only for G code program.............................................................438
10.3.7
Path milling (CYCLE72).......................................................................................................439
10.3.8
Contour pocket/contour spigot (CYCLE63/64).....................................................................443
10.3.9
Predrilling contour pocket (CYCLE64).................................................................................445
10.3.10
Milling contour pocket (CYCLE63).......................................................................................448
10.3.11
Residual material contour pocket (CYCLE63).....................................................................453
10.3.12
Milling contour spigot (CYCLE63)........................................................................................455
10.3.13
Residual material contour spigot (CYCLE63)......................................................................459
10.4
Turning - milling/turning machine.........................................................................................461
10.4.1
General................................................................................................................................461
Milling
Operating Manual, 05/2017, A5E40868956
Table of contents
13
Advertisement
Table of Contents
