Siemens SINUMERIK 840D Function Manual page 489

$AA_EG_DENOM[X, Z] = 0
$P_EG_BC[X] = "NOC"
$AA_EG_NUM_LA[X] = 1
$AA_EG_AX[0, X] = Z
$AA_EG_SYN[X,Z] = <SynPosX_Z>
$AA_EG_SYNFA[X] = <SynPosX>
; ************** Gear Y (G2)
$AA_EG_TYPE[Y, Z] = 1
$AA_EG_NUMERA[Y, Z] = 2
$AA_EG_DENOM[Y, Z] = 0
$P_EG_BC[Y10] = "COARSE"
$AA_EG_NUM_LA[Y] = 1
$AA_EG_AX[0, Y] = Z
$AA_EG_SYN[Y, Z] = <SynPosY_Z>
$AA_EG_SYNFA[Y] = <SynPosY>
; ************** Gear A (G3)
$AA_EG_TYPE[A, Z] = 1
$AA_EG_NUMERA[A, Z] = 3
$AA_EG_DENOM[A, Z] = 0
$P_EG_BC[A10] = "FINE"
$AA_EG_NUM_LA[A] = 1
$AA_EG_AX[0, A] = Z
$AA_EG_SYN[A, Z] = <SynPosA_Z>
$AA_EG_SYNFA[A] = <SynPosA>
; ************** Gear C99 (G4)
$AA_EG_TYPE[C99, Y] = 1
$AA_EG_NUMERA[C99, Y] = 18
$AA_EG_DENOM[C99, Y] = 2
$AA_EG_TYPE[C99, Z] = 1
$AA_EG_NUMERA[C99, Z] = R1 * π
$AA_EG_DENOM[C99, Z] = 1
$AA_EG_TYPE[C99, B] = 1
$AA_EG_NUMERA[C99, B] = 10
$AA_EG_DENOM[C99, B] = 1
$P_EG_BC[C99] = "NOC"
$AA_EG_NUM_LA[C99] = 3
$AA_EG_AX[0, C99] = Y
$AA_EG_AX[1, C99] = Z
$AA_EG_AX[2, C99] = B
$AA_EG_SYN[C99, Y] = <SynPosC99_Y>
$AA_EG_SYN[C99, Z] = <SynPosC99_Z>
$AA_EG_SYN[C99, B] = <SynPosC99_B>
Axes and spindles
Function Manual, 06/2019, A5E47437747B AA
14.4 Electronic gear (EG)
; nominator = 0 → curve table applies
; Block change criterion
; Number of leading axes
; name of leading axis
; Synchronized position of leading axis Z
; Synchronized position of the following axis
; Setpoint value coupling
; curve table No. = 2
; nominator = 0 → curve table applies
; Block change criterion
; Number of leading axes
; name of leading axis
; Synchronized position of leading axis Z
; Synchronized position of the following axis
; Setpoint value coupling
; curve table No. = 3
; nominator = 0 → curve table applies
; Block change criterion
; Number of leading axes
; name of leading axis
; Synchronized position of leading axis Z
; Synchronized position of the following axis
; Setpoint value coupling
; numerator for coupling factor
; denominator for coupling factor
; Setpoint value coupling
; numerator for coupling factor
; denominator for coupling factor
; Setpoint value coupling
; numerator for coupling factor
; denominator for coupling factor
; Block change criterion
; Number of leading axes
; name of leading axis Y
; name of leading axis Z
; name of leading axis B
; Synchronized position of leading axis Y
; Synchronized position of leading axis Z
; Synchronized position of leading axis B
M3: Coupled axes
y
y
z
z
b
b
489