Mitsubishi Electric KD Series User Manual page 48

3-3 Connections
3-3-2 DC5V Connector
V1
Internal Cable connection
Connector : V1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
FPGA ASIC
PWB PWB
Fabricating Cable
1) 2 wires which are connected
1st and 9 th pin, 2 nd and 10 th
pin, 3 rd and 11 th , 4 th and 12 th
pin should be as a twist pair
wiring each other.
2) It is recommended strongly
to connect all pins assigned
as +5V and GND on the pin
connection table .
TM-XG537C
ASIC ASIC
PWB PWB
【 Remarks 】
Please decide the
thickness of the cable in
consideration of the wiring
resistance of the cable.
Recommended cable is
below.
AWG#16-#22
(#16 is recommended)
COPYRIGHT © 2020 MITSUBISHI ELECTRIC CORPORATION. ALL RIGHTS RESERVED.
Be sure to check connection interface (connector joint, wire diameter)
【 Power supply Cable for DC5V 】
* Cable is not in product package.
Prepare it by yourself.
1) To connect V1 connector from 5V power Supple
2) Parts No. of connectors are as following
from CIS unit : DAU-15S-F0R （ JAE ）、
from Power supply ： 030-50634 （ JAE ）、
3) Connector for Power Cable (strongly recommend using)
to CIS unit :DAU-15P-F0R （ JAE ）
* Contact pin :030-50635 （ JAE)
4) Pin connection
No Name
Prod KD6R309MX/M KD6R617MX/
uct X-NL MX-NL
1 +5VP/S +5VPS
2 +5VPS
ＮＣ
3 +5VPS +5VPS
4
ＮＣ ＮＣ
5
ＮＣ ＮＣ
6
ＮＣ ＮＣ
7
ＮＣ ＮＣ
8
ＮＣ ＮＣ
9
ＧＮＤ ＧＮＤ
10
ＮＣ ＧＮＤ
11
ＧＮＤ ＧＮＤ
12
ＮＣ ＮＣ
13
ＮＣ ＮＣ
14
ＮＣ ＮＣ
15
ＮＣ ＮＣ
before using the product.
Symbol
KD6R926MX/M
-
X-NL
+5VPS
ＶＤＤ
+5VPS
ＶＤＤ
+5VPS
ＶＤＤ
+5VPS
ＶＤＤ
ＮＣ
ＮＣ
ＮＣ
ＮＣ
ＧＮＤ ＧＮＤ
ＧＮＤ ＧＮＤ
ＧＮＤ ＧＮＤ
ＧＮＤ ＧＮＤ
ＮＣ
ＮＣ
ＮＣ
48