Tour Sequence - Panasonic WJ-SX550A Operating Instructions Manual

4. Tour Sequence (T-SEQ)
This table is used to programme or edit a Tour Sequence.
There are 32 Tour Sequences available, each with 64 steps.
Each step consists of a camera number, a dwell time, an associated Pan/Tilt preset position address (if applicable), and auxiliary
switches 1 and 2.
No monitor number is assignable as a Tour Sequence will run on any monitor that the user can control.
5
To programme or edit a Tour Sequence do the following:
Note: Before programming or editing a Tour Sequence the Alarm Mode must be in the Off mode first. Follow Alarm Mode Setting
Procedures on page 76.
1. Move the cursor to the 3 position by moving the Joystick Controller. Enter the desired tour sequence number, 1-32, by press-
ing the Numeric Keys, and then pressing the Set (SET) Key.
2. Move the cursor to the 4 position by moving the Joystick Controller. Press the Function (F4) Key to open the Pop Up Window.
Select Auto Skip On or Off by moving the Joystick Controller and then pressing the Set (SET) Key to execute the selection.
3. Move the cursor to the 5 position by moving the Joystick Controller. Enter the desired camera number, 1-128, on each step by
pressing the Numeric Keys.
4. Move the cursor to the 6 position by moving the Joystick Controller. Enter the associated Pan/Tilt preset address number (if
applicable) by pressing the Numeric Keys.
5. Move the cursor to the 7 position by moving the Joystick Controller. Enter the desired Dwell Time, 1-30, by pressing the
Numeric Keys.
6. Move the cursor to the 8 or 9 position by moving the Joystick Controller. Press the Function (F4) Key to open the Pop Up
Window, select AUX On or Off by moving the Joystick Controller and then pressing the Set (SET) Key to execute the selection.
7. Press the function (F1) Key to select the next page or press the Function (F2) Key to select the previous page. Repeat the
above procedures until a tour sequence is completely assembled.
8. When satisfied with all of the above steps, press the Escape (ESC) Key to escape from the programming mode. The cursor
returns to the 3 position.
9. Repeat the above procedures to programme other Tour Sequences.
S e t U p P R O G . T - S E Q
T o u r S e q u e n c e 0 1
A u t o S k i p O n
S t e p 0 1 0 2 0 3 0 4 0 5
C A M 1 0 1 5 0 9 0 0 0 4
P R E 2 0 6 4 1 1 0 9
D W E L L 0 3 0 0 0 1 0 2 0 5
A U X 1
A U X 2
S t e p 1 7 1 8 1 9 2 0 2 1
C A M 0 0 0 0 0 0 0 0 0 0
P R E
D W E L L 0 0 0 0 0 0 0 0 0 0
A U X 1
A U X 2
F 1 : N e x t P a g e F 2 : P r e
0 6 0 7 0 8 0 9 1 0 1 1
0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0
2 2 2 3 2 4 2 5 2 6 2 7
0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0
P a g e F 3 : D E L F 4 : P o p
-70-
P a g e 1 o f 2
1 2 1 3 1 4 1 5 1 6
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
2 8 2 9 3 0 3 1 3 2
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
. . O n . . O f f
U p