Siemens SINUMERIK 840D sl Programming Manual page 10

Table of contents
5.3.5 Calibrating a workpiece probe in the applicate determining probe length ............................... 5-44
5.3.5.1 General information.................................................................................................................. 5-44
5.3.5.2 Programming example ............................................................................................................. 5-46
5.3.5.3 Operational sequence .............................................................................................................. 5-47
5.4 CYCLE977 workpiece: Measure hole/shaft/groove/web/rectangle parallel to axes ................ 5-48
5.4.1 Function overview .................................................................................................................... 5-48
5.4.2 Measuring contour elements.................................................................................................... 5-52
5.4.2.1 General information.................................................................................................................. 5-52
5.4.2.2 Programming example ............................................................................................................. 5-55
5.4.2.3 Operational sequence .............................................................................................................. 5-57
5.4.3 Measuring and tool offset......................................................................................................... 5-61
5.4.3.1 General information.................................................................................................................. 5-61
5.4.3.2 Programming example ............................................................................................................. 5-63
5.4.4 Measurement and ZO determination ....................................................................................... 5-65
5.4.4.1 General information.................................................................................................................. 5-65
5.4.4.2 Programming example ............................................................................................................. 5-67
5.5 CYCLE978 workpiece: Measuring a surface parallel to the axis ............................................. 5-69
5.5.1 Function overview .................................................................................................................... 5-69
5.5.2 Measuring the surface.............................................................................................................. 5-71
5.5.3 Measurement and ZO determination ....................................................................................... 5-73
5.5.3.1 General information.................................................................................................................. 5-73
5.5.3.2 Programming example ............................................................................................................. 5-74
5.5.4 Measuring and tool offset......................................................................................................... 5-76
5.5.4.1 General information.................................................................................................................. 5-76
5.5.4.2 Programming example ............................................................................................................. 5-78
5.6 CYCLE979 workpiece: Measure hole/shaft/groove/rib at an angle ......................................... 5-80
5.6.1 Function overview .................................................................................................................... 5-80
5.6.2 Measure shaft, groove, web..................................................................................................... 5-83
5.6.2.1 General information.................................................................................................................. 5-83
5.6.2.2 Operational sequence .............................................................................................................. 5-85
5.6.3 Measuring and tool offset......................................................................................................... 5-88
5.6.3.1 General information.................................................................................................................. 5-88
5.6.3.2 Programming example ............................................................................................................. 5-90
5.6.4 Measurement and ZO determination ....................................................................................... 5-92
5.6.4.1 General information.................................................................................................................. 5-92
5.6.4.2 Programming example ............................................................................................................. 5-94
5.7 CYCLE998 workpiece: Angle measurement and ZO determination........................................ 5-95
5.7.1 Function overview .................................................................................................................... 5-95
5.7.2 1-angle measurement .............................................................................................................. 5-98
5.7.2.1 General information.................................................................................................................. 5-98
5.7.2.2 Programming example ........................................................................................................... 5-100
5.7.2.3 Operational sequence ............................................................................................................ 5-102
5.7.3 2-angle measurement ............................................................................................................ 5-107
5.7.3.1 General information................................................................................................................ 5-107
5.7.3.2 Programming example 1 ........................................................................................................ 5-108
5.7.3.3 Programming example 2 ........................................................................................................ 5-110
5.7.3.4 Operational sequence ............................................................................................................ 5-113
5.8 CYCLE961 workpiece: Setup inside and outside corner ....................................................... 5-114
5.8.1 Function overview .................................................................................................................. 5-114
5.8.2 Setting up a corner with definition of distances and angles................................................... 5-117
5.8.2.1 General information................................................................................................................ 5-117
5.8.2.2 Programming example ........................................................................................................... 5-119
5.8.2.3 Operational sequence ............................................................................................................ 5-120
5.8.3 Setting up a corner with 4 points............................................................................................ 5-122
x
Programming Manual, Release 04/2006, 6FC5398-4BP10-0BA0
Measuring cycles