Specifications; Specifications - Toro Greensmaster 3200 Service Manual

Specifications

SINGLE POINT ADJUST
Height–of–Cut (HOC): The cutting height is adjusted
on the rear roller by two vertical screws which are held
by two locking capscrews. The bench HOC range is
3/32 inch to 1–1/32 inches (2.4 mm to 26.2 mm). The ef-
fective HOC may vary depending on turf conditions and
the bedknife installed.
Reel Construction: The reels are 5 inches (13 cm) in
diameter and 21 inches (53.3 cm) in length. High carbon
steel blades are welded to 5 stamped steel spiders and
heat treated to RC 48–54 hardness. The reel is ground
for diameter, concentricity, and back grind.
Reel Bearings: An inverted seal is pressed onto the
reel shaft. Two double row ball bearings (30 mm I.D.)
are press fit onto the reel shaft. Bearing side load is
maintained by a 3–1/2 turn wave washer with no adjust-
ing nut.
Reel Drive: The reel weldment shaft is a 1.375 inch
(3.493 cm) diameter tube with drive inserts permanently
pressed into both ends. A replaceable floating coupler
with an internal eight tooth spline is factory installed on
the right end. A snap ring holds the coupler in place. The
floating coupler may be moved to the other end when
the cutting unit is used in the tractor's front right position.
Frame Construction: A single top tube is welded be-
tween two sideplates. A bolt–in cross rod acts to set the
front frame width and stiffen the assembly. The lift straps
have a replaceable roller that may be moved to change
transport height of the cutting unit.
Bedknife: This high carbon steel bedknife is replace-
able, single edged, and austempered to RC 48–55. It is
fastened to a machined cast iron bedbar with 13 screws.
The tournament bedknife is supplied as the standard
bedknife (Part No. 93–4263).
Greensmaster 3200/3200–D
4–BOLT ADJUST
Figure 1
Options:
Micro Cut Bedknife
Low Cut Bedknife
High Cut Bedknife
Fairway Bedknife
Bedknife Adjustment (Single Point Adjust): A single
control screw with detents moves the bedknife 0.0007
inch (0.018 mm) for each indexed position. A linear ad-
justment on the bedbar left end allows leveling of the
bedknife to the reel blades. A centered lever arm regu-
lates the bedknife to reel contact with two rubber bush-
ings acting as pivots.
Bedknife Adjustment (4–Bolt Adjust): Two opposing
screws on each end of the bedbar level and regulate the
bedknife to reel contact.
Front Roller: The standard front roller is a 2.5 inch (6.4
cm) diameter Wiehle. The right bracket provides level-
ing with an eccentric shoulder bolt. A second eccentric
may be added to the left bracket for increased leveling
range. The roller has a through shaft with greaseable
ball bearings.
Rear Roller: The standard rear roller is a smooth roller
with a 2 inch (5.2 cm) diameter. The roller has a through
shaft with greaseable ball bearings.
Front Shield: A snap–in shield covers the lower front
of the reel. The shield helps improve grass throwing into
the basket, and it prevents the basket sealing flap from
being damaged by the reel.
Counterbalance Weight: For easy installation, the
weight has a spin flange like the reel motors. It is
installed opposite the reel motor. It seals the bearing and
balances the reel motor's weight during cutting.
Page 8 – 3
Part No. 93–4262
Part No. 93–4264
Part No. 94–6392
Part No. 94–6393
Cutting Units