Controller - Panasonic GP-X Series User Manual

8.1.2 Controller

Set model name
NPN output GP-XC3S
(Note 1)
PNP output GP-XC3S-P GP-XC5S-P GP-XC8S-P GP-XC10M-P GP-XC12ML-P
Item
Supply voltage
Current consumption
Analog voltage output
Response time
Resolution (Note 3)
Linearity (Note 3)
Temperature
(Note 4)
characteristic
<NPN output type>
NPN open-collector transistor
Maximum sink current: 100mA
Comparison output
Applied voltage: 30V DC or less
Alarm output
Residual voltage: 1.6V or less
Strobe output
Short-circuit
protection
<NPN output type>
Photocoupler input
Input current: 9mA or less
Operating voltage: ON voltage 17V or more
Exter nal input
Input impedance: 5k
Sampling frequency
Zero-set setting method
MODE
HI
GO
LO
TIMINIG
Upper line digital indicator part 5 digit orange LED (display of numerical values out of the upper and lower limit value)
Lower line digital indicator part 5 digit green LED (display of numerical values within the upper and lower limit value)
Ambient
temperature
Ambient
humidity
Noise immunity
Vibration resistance 10 to 55Hz frequency, 0.75mm amplitude in X, Y and Z directions for two hours each
Shock resistance
Grounding method
Material
Weight
Accessory
Notes: 1) GP-XC3S (-P)and GP-XC5S (-P) is applicable to export regulations specified in "Foreign Exchange and Foreign Trade
Control Law". Exportation of the 3S or 5S type or carrying it outside Japan requires an export permit from the Japanease
government. However, GP-XC3SE and GP-XC5SE type which are not applicable to export regulations are also available.
2) The factory shipment setting is between 0 and +5V in the detection range.
3) Value at constant +25
The value is in the range from 20 to 60% of the maximum detection distance with a combination of sensor head
4)
and controller.
GP-XC5S GP-XC8S
24V DC
Output voltage:
Output impedance: 100
0.02% F.S. (64 times average processing)
0.07
(between output and 0V)
(at 100mA sink current)
0.4V (at 16mA sink current)
(between 24V and input)
OFF voltage 4V or less
(between 24V and input)
approx.
Push button setting/External input setting
Orange LED (lights up in mode status)
Orange LED (lights up when the upper value is exceeded)
Green LED (lights up when within the upper and lower limit value)
Orange LED (lights up when less than the lower limit value)
Green LED (lights up as per the external or internal trigger timing)
0 to 50 (No dew condensation), Storage: 0 to
35 to 85%RH, Storage: 35 to 85%RH
Power supply line: 1,000Vp, 10ms cycle, 0.5 s pulse width
Radiation: 300Vp, 10ms cycle, 0.5 s pulse width (with noise simulator)
2
100m/s acceleration (10G approx.) in X, Y and Z directions five times each
Enclosure: Polycarbonate
ATA4811 (Controller mounting bracket): 1 set
GP-XC10M GP-XC12ML GP-XC22KL GP-XC3SE GP-XC5SE
GP-XC22KL-P GP-XC3SE-P GP-XC5SE-P
10% Ripple P-P 10% or less
150mA or less
5 to 5V (Note 2)
approx.
0.075ms (Fastest)
Within 0.3% F.S.
/F.S./ or less
<PNP output type>
PNP open-collector transistor
Maximum source current: 100mA
Applied voltage: 30V DC or less
Residual voltage: 1.6V or less
0.4V (at 16mA source current)
Incorporated
<PNP output type>
Photocoupler input
Input current: 9mA or less
Operating voltage: ON voltage 17V or more
Input impedance: 5k
40kHz (25 s)
Floating earth
120g approx.
0.04% F.S. (64 times average processing)
(between output and V)
(at 100mA source current)
(between 0V and input)
OFF voltage 4V or less
(between 0V and input)
approx.
50
139