Kenwood TK-5810 Service Manual page 68

TK-5810 BG
(
Item
Panel tuning mode
11. DTMF 1) Adj item: [DTMW]
Deviation Adjust: [✳✳✳]
write *4 Deviation meter
(Wide) LPF: 15kHz
HPF: OFF
Detector: ±PEAK/2
PTT: ON
Press [PF5] key to
store the adjust-
ment value.
(Narrow) 1) Adj item: [DTMN]
Adjust: [✳✳✳]
Deviation meter
LPF: 15kHz
HPF: OFF
Detector: ±PEAK/2
PTT: ON
Press [PF5] key to
store the adjust-
ment value.
12. Single 1) Adj item: [2TNW]
Tone Adjust: [✳✳✳]
Deviation Deviation meter
write *4 LPF: 15kHz
(Wide) HPF: OFF
Detector: ±PEAK/2
PTT: ON
Press [PF5] key to
store the adjust-
ment value.
(Narrow) 1) Adj item: [2TNN]
Adjust: [✳✳✳]
Deviation meter
LPF: 15kHz
HPF: OFF
Detector: ±PEAK/2
PTT: ON
Press [PF5] key to
store the adjust-
ment value.
13. MSK 1) Adj item: [MSKW]
Deviation Adjust: [✳✳✳]
write *4 Deviation meter
(Wide) LPF: 15kHz
HPF: OFF
Detector: ±PEAK/2
PTT: ON
Press [PF5] key to
store the adjust-
ment value.
*4: Refer to the "Necessary Deviation adjustment item for each signaling and mode" table on page 69.
Balance adjustment is common with the adjustment of all signaling deviation.
68
/5810H BG
) ( )
ADJUSTMENT
Condition
PC test mode
equipment
1) Adj item: [DTMF Deviation
Deviation (Wide)] meter
Deviation meter Oscilloscope
LPF: 15kHz
HPF: OFF
Detector: ±PEAK/2
PTT: Press [Trans-
mit] button.
Press [OK] button
to store the adjust-
ment value.
1) Adj item: [DTMF
Deviation (Narrow)]
Deviation meter
LPF: 15kHz
HPF: OFF
Detector: ±PEAK/2
PTT: Press [Trans-
mit] button.
Press [OK] button
to store the adjust-
ment value.
1) Adj item: [Single
Tone Deviation
(Wide)]
Deviation meter
LPF: 15kHz
HPF: OFF
Detector: ±PEAK/2
PTT: Press [Trans-
mit] button.
Press [OK] button
to store the adjust-
ment value.
1) Adj item: [Single
Tone Deviation
(Narrow)]
Deviation meter
LPF: 15kHz
HPF: OFF
Detector: ±PEAK/2
PTT: Press [Trans-
mit] button.
Press [OK] button
to store the adjust-
ment value.
1) Adj item: [MSK
Deviation (Wide)]
Deviation meter
LPF: 15kHz
HPF: OFF
Detector: ±PEAK/2
PTT: Press [Trans-
mit] button.
Press [OK] button
to store the adjust-
ment value.
Measurement
Test-
Unit Terminal Unit
Rear ANT
panel
Adjustment
Specifi cations /
Parts Method
[Panel Write the value as ±100Hz
tuning followings.
mode] 170 (Reference
[PF3] value)
[PF4]
3.00kHz
[PC test
mode]
[ ],[ ]
Write the value as ±50Hz
followings.
171 (Reference
value)
1.50kHz
Write the value as ±100Hz
followings.
133 (Reference
value)
3.00kHz
Write the value as ±50Hz
followings.
133 (Reference
value)
1.50kHz
Write the value as ±100Hz
followings.
132 (Reference
value)
3.00kHz
Remarks