Kenwood TK-5810 Service Manual page 8

TK-5810 BG
(
11. Clone Mode
Programming data can be transferred from one trans-
ceiver to another by connecting them via their microphone
jacks. The operation is as follows (the transmit transceiver
is the source and the receive transceiver is a target).
The following data cannot be cloned.
• Tuning data
• Embedded message with password
• Model name data
• ESN (Electronic Serial Number) data
• Network fi le data (P25)
Key guide on the "INPUT PASSWORD" display.
1. Press and hold the [PF5] key while turning the trans-
ceiver power ON. If the Read authorization password is
set to the transceiver, the transceiver displays "CLONE
LOCK". If the password is not set, the transceiver dis-
plays "CLONE MODE".
2. When you enter the correct password, and "CLONE
MODE" is displayed, the transceiver can be used as the
cloning source. The following describes how to enter
the read authorization password.
3.
• How to enter the read authorization password using
the microphone keypad;
If one of keys 0 to 9 is pressed while "CLONE LOCK" is
displayed, the pressed number is displayed on the LCD.
Each press of the key shifts the display in order to the
left.
If you press the [#] key, the least digit of the password is
deleted.
When you enter the password and press the [ ] key,
"CLONE MODE" is displayed if the entered password is
correct. If the password is incorrect, "CLONE LOCK" is
redisplayed.
• How to enter the read authorization password using
the [Selector] knob;
If the [Selector] knob is rotated while "CLONE LOCK"
is displayed, the number (0 to 9) flashes on the LCD.
When you press the [GRP
number is determined. If you press the [PF3] key, the
least digit of the password is deleted. If you press the
[PF2] key after entering the password in this procedure,
"CLONE MODE" is displayed if the entered password is
correct. If the password is incorrect, "CLONE LOCK" is
redisplayed.
4. Power ON the target transceiver.
5. Connect the cloning cable (part No. E30-3370-05) to the
microphone jacks on the source and target.
6. Press the [PF2] key on the source while the source dis-
plays "CLONE MODE". The data of the source is sent to
the target. While the target is receiving the data, "PRO-
GRAM" is displayed. When cloning of data is completed,
the source displays "END", and the target automatically
operates in the User mode. The target can then be oper-
ated by the same program as the source.
8
/5810H BG
) ( )
REALIGNMENT
] key, the currently selected
7. The other target can be continuously cloned. When
the [PF2] key on the source is pressed while the source
displays "END", the source displays "CLONE MODE".
Carry out the operation in step 4 to 6.
Note:
• You cannot clone transceivers using hardware versions
1.0 or 2.0.
Cloning is only possible when both transceivers are us-
ing hardware version 3.0.
• Cannot be cloned if the overwrite password is pro-
grammed to the target.
• "Model Name and Market Code", "Head Confi guration"
and "Head Type" must be same to clone the transceiver.
However, it may be unable to clone the transceiver de-
pending on the enhanced features settings.
(Refer to the FPU for the enhanced features details.)
• Under certain conditions, clone mode cannot be acti-
vated even if the clone mode of the source transceiver,
using Hardware Version 3.0, is set to enable. Refer to
the FPU for more details.
• Can not clone if the checksum in the Network File area
of the source transceiver and the target transceiver is dif-
ferent.
Cloning cable
(E30-3370-05)