NEC Express5800 Series Maintenance Manual page 196

Chapter 3 Appendix
Error Message
9021 Unsupported CPU Speed detected
on CPU #1
9022 Unsupported CPU Speed detected
on CPU #2
9040 PEI_CPU_SELF_TEST_FAILED
9041 Detected CPU Error on CPU #1
9042 Detected CPU Error on CPU #2
9060 PEI_CPU_MISMATCH
9080 Link in Slow Speed Mode between
CPU1 and CPU2.
9081 Link Failure between CPU1 and
CPU2.
9082 Link Width Error between CPU1
and CPU2.
9E80 Forced to use CPU with error. A CPU error occurred, but forced to
A001 Memory Error detected in
CPU1_DIMM1
A002 Memory Error detected in
CPU1_DIMM2
A003 Memory Error detected in
CPU1_DIMM3
A004 Memory Error detected in
CPU1_DIMM4
A005 Memory Error detected in
CPU1_DIMM5
A006 Memory Error detected in
CPU1_DIMM6
A00D Memory Error detected in
CPU2_DIMM1
A00E Memory Error detected in
CPU2_DIMM2
A00F Memory Error detected in
CPU2_DIMM3
A010 Memory Error detected in
CPU2_DIMM4
A011 Memory Error detected in
CPU2_DIMM5
A012 Memory Error detected in
CPU2_DIMM6
A420 Online Spare Memory was not
ready.
A421 Mirroring Memory was not
ready.
A423 Lockstep was not ready.
A42 Cluster On Die was not
8 ready.
A42 DIMM population is
9 insufficient for Cluster On
Die.
A800 Memory not detected
A804 Latest memory module is
corrupted.
AE01 CPU1_DIMM1 has been disabled. A memory error was detected.
CPU1_DIMM2 has been disabled. A memory error was detected.
AE02
196
Cause
A CPU having an unsupported clock
speed was detected.
An error occurred in CPU
initialization.
An error occurred on CPU #1.
An error occurred on CPU #2.
The type of CPU in slot CPU#1
differs from that in CPU#2.
Slow Speed Mode was detected on
a bus between CPU1 and CPU2.
Link failure was detected on a bus
between CPU1 and CPU2.
Link width error was detected on a
bus between CPU1 and CPU2
use the CPU.
An error was detected on
CPU1_DIMM1.
An error was detected on
CPU1_DIMM2.
An error was detected on
CPU1_DIMM3.
An error was detected on
CPU1_DIMM4.
An error was detected on
CPU1_DIMM5.
An error was detected on
CPU1_DIMM6.
An error was detected on
CPU2_DIMM1.
An error was detected on
CPU2_DIMM2.
An error was detected on
CPU2_DIMM3.
An error was detected on
CPU2_DIMM4.
An error was detected on
CPU2_DIMM5.
An error was detected on
CPU2_DIMM6.
Failed to enable the Sparing feature
by the current memory
configuration.
Failed to enable the Mirroring
feature by the current memory
configuration.
Failed to enable the LockStep
feature by the current memory
configuration.
Failed to enable the Cluster On Die
feature by the current hardware
configuration.
Failed to enable the Cluster On Die
feature by the current memory
configuration.
No available memory is installed.
The BIOS flash memory was failed.
CPU1_DIMM1 has been disabled.
CPU1_DIMM2 has been disabled.
Express5800/B120f Maintenance Guide
1. Error Message of POST and Virtual LCD
Solution
Contact your sales representative.
Start SETUP, and confirm the settings of
Memory RAS Mode. When Memory
Sparing, Memory Mirroring, or Memory
LockStep feature is enabled, POST
detects this error if DIMMs are degraded.
Start SETUP, and specify Yes for
Memory Retest, then execute Save
Changes and Exit. If the same error
persists, contact your sales
representative.
Replace with a processor that supports
this feature, or start SETUP and disable
Cluster On Die. If this does not resolve
the problem, contact your sales
representative.
Check if the memory configuration is
proper. If this does not resolve the
problem, contact your sales
representative.
Check if DIMMs are properly installed. If
the same error persists, contact your sales
representative.
Contact your sales representative.