Switching The Me Area In The Control Panel Av-Hs60C2/Av-Hs60C4 - Panasonic Live Production Suite Series Operating Manual

FTB (Fade to Black)
For DSKPGM1 and DSKPGM2 outputs, fade out from the program image to the black background screen, and fade in from the black ground screen
to the program image. While the settings and transition are performed by the menu, use the macro memory to assign to certain buttons to execute
transition.
1
Select the <OPR> button → [OTHER SETTINGS] → [Transition] tab.
2
Select an item in [Source] in the [FTB] column.
f Select the image for fading out.
[Still1], [Still2]
[Clip1], [Clip2]
[CBGD1], [CBGD2]
[White]
[Black]
3
Set [Time] in the [FTB] column.
f Set the transition time.
4
Set [FTB On] in the [FTB] column.
f When [FTB On] is selected, the screen fades out to the image selected in the step
If [FTB On] is selected when the image selected in the step
If [FTB On] is selected during transition, the transition direction is reversed.
@ NOTE
t If an item other than [White] or [Black] is selected in [Source] in the [FTB] column, the corresponding crosspoint buttons will light in red while [FTB On]
is set.
AUX1 to AUX4 bus transitions
In the AUX1 to AUX4 buses, MIX transition is available.
1
Select the <OPR> button → [OTHER SETTINGS] → [Transition] tab.
2
Select an item in [AUX1] to [AUX4] in the [AUX Trans] column.
[OFF]
[ON]
3
Set [AUX1] through [AUX4] in the [Trans Time] column.
f Set the transition time.
r AUX bus transition operation
AUX AUX AUX AUX AUX AUX
1/2 3/4 5/6 7/8 9/10 11/12
C9 C10 C11 C12 C9 C10
Blinks in the Low tally color (during transition)
Lights in the Preset tally color
Set [AUX1] to [AUX4] to [ON] in the [AUX Trans] column, then select sources with the relevant AUX bus crosspoint buttons.
At this time, the MIX transition is performed at the transition time specified in [AUX1] to [AUX4] in the [Trans Time] column.
During transition, KEY crosspoint buttons denoting the transition source lights in the Preset tally color, and the KEY bus crosspoint buttons denoting the
transition target source lights in the Low tally color.
When the transition is completed, the transition source button goes off, and the transition target button lights in the Low tally color.
When another signal is selected during transition, the transition processing continues from that midway point.

Switching the ME area in the Control Panel AV-HS60C2/AV-HS60C4

Switch the ME1 and ME2 in the Control Panel AV-HS60C2/AV-HS60C4.
f The following figure shows the area that can be switched.
Chapter 7 Configuring Operations — Setting the operation mode
Uses still image video memory (Still1, Still2).
Uses moving image video memory (Clip1, Clip2).
Uses the color background.
Uses the white background.
Uses the black background.
Disables the MIX translation.
Enables the MIX translation.
AUX AUX AUX AUX AUX AUX USK1 USK2 USK3
13/14 15/16 17/18 19/20 21/22 23/24 F/S F/S F/S
C11 C12 C9 C10 C11 C12 V1 V2 V3
2
at a specified transition time.
2
is on the screen, the screen fades in to the program image.
USK4 VMEM DSK1 DSK2 DSK3 DSK4
DISP MCRO
F/S F/S F/S F/S F/S
CG CG CG CG STIL STIL
V4 V5 V6
1V 2V 3V 4V 1V
– 119 –
F/S
STIL STIL CLIP CLIP CLIP CLIP4
BC1 BC2
2V 3V 4V 1V 2V 3V V
ME1 ME2 ME3 ME4