Mitsubishi Electric 800 Series Instruction Manual page 373

(M) Monitor display and monitor output signal
Setting
Signal
Positive Negative
name
logic logic
30 130 Y30
31 131 Y31
32 132 Y32
33 133 RY2
34 134 LS
35 135 TU
36 136 Y36
38 138 MEND
39 139 Y39
40 140 Y40
41 141 FB
42 142 FB2
43 143 FB3
44 144 RUN2
45 145 RUN3
46 146 Y46
47 147 PID
48 148 Y48
49 149 Y49
50 150 Y50
51 151 Y51
52 152 Y52
53 153 Y53
54 154 Y54
55 155 For manufacturer setting. Do not set.
56 156 ZA
57 157 IPM
60 160 FP
372
PARAMETERS
Function
Forward rotation output
(for vector control
compatible option)

Reverse rotation output
(for vector control
compatible option)

Regenerative status output
(for vector control
compatible option)

Operation ready 2
Low speed detection
Torque detection
In-position
Travel completed
Start time tuning completion Output when tuning is completed during start-up.
Trace status
Speed detection
Second speed detection
Third speed detection
Inverter running 2
Inverter running and start
command is ON
During deceleration at
occurrence of power failure
During PID control activated Output during PID control.
PID deviation limit
During pre-charge operation
During second pre-charge
operation
Pre-charge time over
Second pre-charge time
over
Pre-charge level over
Second pre-charge level
over
Home position return failure
During PM sensorless vector
control
Position detection level
Operation
Output during motor forward rotation.
Output during motor reverse rotation.
Output when the regenerative status is entered
under vector control.
Output during pre-excitation or operation under
Real sensorless vector control and vector control.
Output when the output frequency drops to the
Pr.865 setting or lower.
Output when the motor torque is higher than the
Pr.864 setting.
Output when the number of droop pulses drops
below the setting.
Output when the droop pulse is within the in-
position width, and the position command
operation is not completed or performing home
position return.
Output during trace operation.
Output when the actual motor rotations per minute
(estimated rotations per minute) reaches Pr.42
(Pr.50, Pr.116).
Output while the forward rotation or reverse
rotation signal is ON.
Output during deceleration even while the forward
rotation or reverse rotation signal is OFF. (Not
output while pre-excitation LX is ON.)
Output also while the orientation command (X22)
signal is ON.
Under position control, turns ON when the servo is
turned ON (LX ON). (Turns OFF when the servo
turned is OFF (LX OFF)).
Output while the inverter is running and the start
command is ON.
Output after the power-failure deceleration
function operates.
(Retained until canceled.)
Output when the absolute deviation value exceeds
the limit value.
Output during pre-charge operation.
Output when the pre-charge operation reaches
the time limit set in Pr.764 or Pr.769.
Output when the measured value before reaching
the ending time during pre-charge operation is
higher than the detection level set in Pr.763 or
Pr.768.
Output while a home position return failure
warning is occurring.
Output while the control method is PM sensorless
vector control.
Output when the current position exceeds the
position detection judgment value (Pr.1294 and
Pr.1295).
Refer
Related
to
parameter
page
377
― 377
377
― 375
Pr.865 379
Pr.864 384
Pr.426 234
Pr.426 234
Pr.95, Pr.574 444
Pr.1020 to Pr.1047 533
Pr.42, Pr.50,
379
Pr.116
― 375
― 375
Pr.261 to Pr.266 526
Pr.127 to Pr.134,
488
Pr.575 to Pr.577
Pr.127 to Pr.134,
488
Pr.553, Pr.554
Pr.127 to Pr.134,
Pr.241, Pr.553,
Pr.554,
504
Pr.575 to Pr.577,
Pr.753 to Pr.769,
C42 to C45
― 207
Pr.71, Pr.80,
145
Pr.998
Pr.1294 to Pr.1297 234