Operating Procedures - Sharp PN-L803C Service Manual

CHAPTER 4. SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES

1. OPERATING PROCEDURES

1-1. SERVICE MENU 1
Model name, S/N., firmware version/check sum, usage time etc
are indicated.
MODEL Model name
S/N Serial number
INTEGRATED Integrated version of the firmware
VERSION This is the version for unifying each firmware.
VER(MAIN) Version of the main firmware
When the version combination with the sub
firmware is not correct, "NG" is displayed.
C/S Check sum of the main firmware (capital character)
VER(SUB) Version of the sub firmware
When the version combination with the main
firmware is not correct, "NG" is displayed.
C/S Check sum of the sub firmware (capital character)
VER(TPFW) Version of the touch panel firmware
C/S Check sum of the touch panel firmware (capital
character)
VER(TPCON) Version of the touch panel controller firmware
C/S Check sum of the touch panel controller firmware
(capital character)
VER(DPRX) Version of the Displayport RX microcomputer
firmware
C/S Check sum of the Displayport RX microcomputer
firmware (capital character)
VER(DPTX) Version of the Displayport TX microcomputer
firmware DisplayPort
C/S Check sum of the Displayport TX microcomputer
firmware (capital character)
VER(DSD) Version of the double speed drive module firmware.
VER(KEY) Version of the microcomputer firmware for the
electrostatic key.
VER(LCD) Version of the LCD control IC
USAGE TIME Usage time
ADJUSTMEMT When the white balance setting is reset to the initial
CHECK value after replacement of the PWB or the panel,
"W/BW" is displayed.
When the calibration setting value is reset to the
initial value, "CALIB" is displayed. (Normally it is not
displayed.)
PN-L803C/80TBC3 SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES 4 - 1
1) Press the [SIZE] button of the remote control for about 5
seconds (the LED blinks, and the "F" mark is displayed in the
upper left corner of screen.), press the [BRIGHT- ( )], [VOL -
()] , [BRIGHT+ ()] and [VOL+ ()] button in sequence.
SERVICE MENU1
SERVICE1
MODEL ： PNxxxxx
SERVICE2
INTEGRATED VERSION
VER (MAIN) : OK Ver X.X X
SERVICE3
VER (SUB) : OK Ver X.XX.XX (XXXXXX)C/S：OK
VER (TPFW) : OK Ver X.X X
VER (TPCON) : OK Ver X.X X
VER (DP RX) : OK Ver X.X.X.XXX
VER (DP TX) : OK Ver X.X.X.X
VER (DSD) : OK Ver X.X X
VER(LCD) : OK XXXXXXXXXXXXXXXXXX
USAGE TIME
ADJUSTMENT CHECK
(MEMO)
- Immediately after turning on the power, "CALCULATING" is
displayed for the checksum for a while, and the result is
dipslayed.
- "F" mark is displayed in red when the adjustment lock is set to
other than "Not" and displayed in blue when the OSD display is
set to "Not" or "ON 2".
green. (The red color of "F" mark takes priority.)
1/1
S/N ： XXXXXXXX
： Ver XXXXXXX
(XXXXXX) C/S：OK X X X X X X X XXX
X X X X X X X X
C/S：OK X X X X X X X X
C/S：OK X X X X X X X X
C/S：OK X X X X X X X X
C/S：OK X X X X X X X X
VER(KEY) : OK Ver. X.XX
： XXXH
： W/B CALIB
END・・・[MENU]
For the other cases, it is displayed in