Panasonic AU-EVA1 Operating Instructions Manual page 93

@ NOTE
t This is not displayed in the output from the <SDI OUT> terminal when the menu is displayed in the LCD monitor.
t When the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], this cannot be set.
[MARKER DISP]
Sets if the marker set in [SDI/HDMI MARKER] is displayed or not in the output from the <SDI OUT> terminal.
The items that can be set are as follows.
f [ON], [OFF]
(Factory setting: [OFF])
@ NOTE
t When the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], this cannot be set.
[MENU DISP]
Sets if the menu is displayed or not in the output from the <SDI OUT> terminal.
The items that can be set are as follows.
f [ON], [OFF]
(Factory setting: [ON])
@ NOTE
t Even if [MENU DISP] is set to [OFF], the menu is displayed in the output from the <SDI OUT> terminal during the thumbnail screen.
t When the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], this cannot be set.
[HDMI OUT]
[SIGNAL SEL]
Sets the output from the <HDMI> terminal.
[HDMI]
[LCD(1080p)]
(Factory setting: [HDMI])
@ NOTE
t Following functions are not displayed even when [LCD(1080p)] is set.
‑ Focus square display
‑ Waveform monitor
‑ Zebra pattern when the skin tone detail function is set to enable
t When set to [LCD(1080p)], [HDMI TC OUT] is disabled.
[OUT FORMAT]
Selects the signal to be output from the <HDMI> terminal. The items that can be selected differ depending on the setting in the [SYSTEM SETTINGS]
menu → [SYSTEM MODE] → [FREQUENCY]/[MAIN PIXEL].
[4096x2160p]
[4096x2160p(420/8bit)]
[3840x2160p]
[3840x2160p(420/8bit)]
[1920x1080p]
[1920x1080i]
[1280x720p]
[720x480p]
[720x576p]
(Factory setting: [1920x1080p])
@ NOTE
t For the combination that can be set, refer to "Format that can be output from the <HDMI> terminal".
t It will be fixed to [1920x1080p] when the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], and the
[OUTPUT SETTINGS] menu → [HDMI OUT] → [SIGNAL SEL] is set to [HDMI].
[HDMI TC OUT]
Sets if the time code information is output or not in the output from the <HDMI> terminal.
The items that can be set are as follows.
f [ON], [OFF]
(Factory setting: [OFF])
@ NOTE
t When the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], this cannot be set.
t When the [OUTPUT SETTINGS] menu → [HDMI OUT] → [SIGNAL SEL] is set to [LCD(1080p)], this cannot be set.
Chapter 4 Operation — Menu setting contents
Outputs the signal set in [OUT FORMAT] of [HDMI OUT].
Outputs the video displayed on the LCD monitor in 1920×1080p.
Outputs in 4096×2160p (4:2:2/10 bits).
Outputs in 4096×2160p (4:2:0/8 bits).
Outputs in 3840×2160p (4:2:2/10 bits).
Outputs in 3840×2160p (4:2:0/8 bits).
Outputs in 1920×1080p.
Outputs in 1920×1080i.
Outputs in 1280×720p.
Outputs in 720×480p.
Outputs in 720×576p.
– 93 –