Table of Contents
Advertisement
20 FUNCTION PORT
Function Name
Scan On
Scan On/Off
Scrambler Off
Scrambler On
Scrambler
On/Off
Squelch Off
Squelch On
Squelch On/Off
TA Line
Pre-emphasis On/Off
Test Tone Off
Test Tone On
Test Tone
On/Off
TOT Disable*1
TOT Enable*1
TOT Disable/Enable*1
TX Disable
TX Enable
TX Disable/Enable
49
The Scan is enabled when a signal is applied to the PF [Scan On] input port.
When the signal is detected with the Down Edge, you cannot disable the Scan after this function
is once enabled. It should be used with Off function.
The Scan On/Off is switched enable and disable when a signal is applied to the PF [Scan On/Off]
input port. You can use this function only when the signal is detected with the Down Edge.
to 20.2.1 Trigger Detection for Auxiliary Input Ports.)
The Scrambler function is disabled when a signal is applied to the PF [Scrambler Off] input port.
You cannot configure this function when the optional Scrambler board is not installed in TKR-750/
850/751/851.
When the signal is detected with the Down Edge, you cannot switch the Scrambler operation On
after this function is once enabled. So it should be used with On function.
The Scrambler function is enabled when a signal is applied to the PF [Scrambler On] input port.
You cannot configure this function when the optional Scrambler board is not install in TKR-750/
850/751/851.
When the signal is detected with the Down Edge, you cannot disable the Scrambler function after
this function is once enabled. So it should be used with Off function.
The Scrambler operation is switched On/Off when a signal is applied to the PF [Scrambler On/Off]
input port.
You cannot configure this function when the optional Scrambler board is not installed in TKR-750/
850/751/851. You can use this function only when the signal is detected with the Down Edge.
(Refer to 20.2.1 Trigger Detection for Auxiliary Input Ports.)
The Squelch function is disabled when a signal is applied to the PF [Squelch Off] input port.
When a signal is detected with the Down Edge, you cannot switch the Squelch function On when
this function is once enabled. It should be used with Enable function.
The Squelch function is enabled when a signal is applied to the PF [Squelch On] input port.
When a signal is detected with the Down Edge, you cannot switch the Squelch function Off after this
function is once enabled. It should be used with Disable function.
The Squelch function is switched On/Off when a signal is applied to the PF [Squelch On/Off] input
port. You can use this function only when the signal is detected with the Down Edge.
20.2.1 Trigger Detection for Auxiliary Input Ports.)
The pre-emphasis of the TA terminal input signal is switched Enable and Disable.
The Test Tone is Off when the signal is applied to the PF [Test Tone Off] input port.
When a signal is detected with the Down Edge, you cannot switch the Test Tone On after this
function is once enabled. It should be used with On function.
The Test Tone is On when the signal is applied to the PF [Test Tone On] input port.
When a signal is detected with the Down Edge, you cannot switch the Test Tone Off after this
function is once enabled. It should be used with Off function.
The Test Tone is switched On and Off when a signal is applied to the PF [Test Tone On/Off] input
port. You can use this function only when the signal is detected with the Down Edge.
20.2.1 Trigger Detection for Auxiliary Input Ports.)
The Time Out Timer is Off when a signal is applied to the PF [TOT Disable] input port.
When the signal is detected with the Down Edge, you cannot switch the Time Out Timer On when
this function is once enabled. It should be used with On function.
The Time Out Timer is On when a signal is applied to the PF [TOT Enable] input port.
When the signal is detected with the Down Edge, you cannot switch the Time Out Timer Off after
this function is once enabled. It should be used with Off function.
The Time Out Timer is switched On and Off when a signal is applied to the PF [TOT Disable/
Enable] input port. You can use this function only when the signal is detected with the Down
Edge.
(Refer to 20.2.1 Trigger Detection for Auxiliary Input Ports.)
All transmissions is restricted when a signal is applied to the PF [TX Disable] input port.
When the signal is detected with the Down Edge, you cannot permit transmissions after this
function is once enabled. It should be used with Enable function.
All transmissions is permitted when a signal is applied to the PF [TX Enable] input port.
When the signal is detected with the Down Edge, you cannot restrict transmissions after this
function is once enabled. It should be used with Disable function.
The transmissions is switched disable/enable when a signal is applied to the PF [TX Disable/
Enable] input port. You can use this function only when the signal is detected with the Down
Edge.
(Refer to 20.2.1 Trigger Detection for Auxiliary Input Ports.)
Function Reference (FUNC)
Description
(Refer
(Refer to
(Refer to
Version: 1.01 USA
Advertisement
Table of Contents
