Table of Contents
Advertisement
22 CW ID/CW MESSAGE
22.1.11Encode with QT/DQT (CW ID)
Encode with QT/DQT is a function to encode a QT/DQT
(Primary) code configured to each channel while sending
the CW ID.
Note: TKR-750/850/751/851 sends the QT/DQT code configured
to each channel when the Encode with QT/DQT function is
enabled, and it does not send the QT/DQT code when the
Encode with QT/DQT function is disabled. However, the
newly configured CW ID/CW Message is sent
corresponding to the Encode with QT/DQT configuration
when TKR-750/850/751/851 sends another CW ID or CW
Message while the CW ID is independently sent.
22.2 CW Message.)
! Configuration of KPG-91D
" Configuring the Encode with QT/DQT (Refer to
FPRG 6.3.11 Encode with QT/DQT (CW ID).)
22.2 CW Message
CW Message is a function to transmit the configured
Morse code by interlocking with the PF keys and the AUX
I/O port. It is possible to configure 8 messages with a
maximum of 32 characters and symbols. (Refer to FPRG
13 Function List.)
You can control a transmission of the CW Message with
the following functions.
•
Key Function
TKR-750/850/751/851 transmits a CW Message when
the PF key is pressed if the CW Message
transmission function is assigned on it.
Available Functions.)
•
Auxiliary Input port
TKR-750/850/751/851 transmits a CW Message when
a signal is applied to an Auxiliary Input port if the CW
Message transmission function is assigned on it.
(Refer to 20.2 AUXI Function.)
•
Save On/Off Function
TKR-750/850/751/851 transmits a CW Message when
it enters/exists Save mode if the CW Message
transmission function is assigned to the Save On/Off
function.
(Refer to Table 10-1 Available functions.)
•
Start Up Function
TKR-750/850/751/851 transmits a CW Message when
it is turned ON if the CW Message transmission
function is assigned to the Start Up function.
Table 10-1 Available functions.)
•
Backup Power Function
TKR-750/850/751/851 transmits a CW Message when
the power TKR-750/850/751/851is switched from the
main power to the backup power if the CW Message
55
transmission function is assigned to the Backup
Power function.
functions.)
•
Main Power Function
TKR-750/850/751/851 transmits a CW Message when
the power is switched from the backup power to the
main power if the CW Message transmission function
is assigned to the Main Power function.
Table 10-1 Available functions.)
You can configure the following functions relating to the
(Refer to
transmission of the CW Message by KPG-91D.
CW Message
CW Speed
CW Mod. Delay Time
Audio Frequency
Send CW Message to RA
Encode with QT/DQT (CW ID)
22.2.1 CW Message
You can configure 8 messages with a maximum of 32
characters and symbols.
Characters and
A,B...Y,Z
(
)
(Refer to 15.1
+
" "
?
-
Space
0 - 9
=
/
.
,
'
(Refer to
:
! Configuration of KPG-91D
" Configuring the CW Message (Refer to FPRG
Function Reference (FUNC)
(Refer to Table 10-1 Available
Table 22-2 Available Characters/Symbols
symbols
Alphabet (Upper case characters)
Left parenthesis
Right parenthesis
Adding symbol
Quotation mark
Question mark
Continuous line, subtracting symbol,
horizontal line
Space (You cannot enter the space
continuously or use it as the first letter of
the message.)
Numbers
Double line
Slash
Period
Comma
Abbreviation mark
Colon
6.12.1 CW Message.)
(Refer to
Description
Version: 1.01 USA
Advertisement
Table of Contents
