Mitsubishi Electric F700 Instruction Manual page 59

3.13 Energy saving operation and energy saving monitor
3.13.1 Energy saving control and optimum excitation control (Pr.60) ......................................................................... 118
3.13.2 Energy saving monitor (Pr. 891 to Pr. 899)....................................................................................................... 119
3.14 Motor noise, noise reduction
3.14.1 PWM carrier frequency and Soft-PWM control (Pr.72, Pr.240, Pr.260)........................................................... 124
3.15 Frequency setting by analog input (terminal 1, 2, 4)
3.15.1 Analog input selection (Pr.73, Pr.267)............................................................................................................... 125
3.15.2 Analog input compensation (Pr.73, Pr.242, Pr.243, Pr.252, Pr.253) ............................................................... 127
3.15.3 Input filter time constant (Pr.74) ........................................................................................................................ 128
3.15.4 Bias and gain of frequency setting voltage (current)
(Pr. 125, Pr. 126, Pr. 241, C2(Pr. 902) to C7(Pr. 905))..................................................................................... 129
3.15.5 4mA input check of current input (Pr. 573)........................................................................................................ 134
3.16 Misoperation prevention and parameter setting restriction
3.16.1 Reset selection/disconnected PU detection/PU stop selection (Pr.75)............................................................ 136
3.16.2 Parameter write disable selection (Pr.77) ......................................................................................................... 139
3.16.3 Reverse rotation prevention selection (Pr.78)................................................................................................... 140
3.16.4 Display of applied parameters and user group function (Pr.160, Pr.172 to Pr.174) ........................................ 140
3.17 Selection of operation mode and operation location
3.17.1 Operation mode selection (Pr. 79) .................................................................................................................... 142
3.17.2 Operation mode at power on (Pr. 79, Pr. 340).................................................................................................. 150
3.17.3 Operation command source and speed command source during
communication operation (Pr. 338, Pr. 339, Pr. 550, Pr. 551).......................................................................... 151
3.18 Communication operation and setting
3.18.1 Wiring and configuration of PU connector......................................................................................................... 156
3.18.2 Wiring and arrangement of RS-485 terminals................................................................................................... 158
3.18.3 Initial settings and specifications of RS-485 communication
(Pr. 117 to Pr. 124, Pr. 331 to Pr. 337, Pr. 341)................................................................................................ 161
3.18.4 Communication EEPROM write selection (Pr. 342) ......................................................................................... 162
3.18.5 Mitsubishi inverter protocol (computer link communication)............................................................................. 163
3.18.6 Modbus-RTU communication specifications (Pr. 331, Pr. 332, Pr. 334, Pr. 343, Pr. 549).............................. 173
3.19 Special operation and frequency setting
3.19.1 PID control (Pr. 127 to Pr. 134, Pr. 575 to Pr. 577) .......................................................................................... 184
3.19.2 Commercial power supply-inverter switchover function (Pr. 135 to Pr. 139, Pr. 159) ..................................... 192
3.19.3 Advanced PID function (pump function) (Pr. 575 to Pr. 591) ........................................................................... 197
3.19.4 Traverse function (Pr. 592 to Pr. 597) ............................................................................................................... 206
3.19.5 Regeneration avoidance function (Pr.882 to Pr.886)........................................................................................ 208
3.20 Useful functions
3.20.1 Cooling fan operation selection (Pr.244)........................................................................................................... 210
3.20.2 Display of the life of the inverter parts (Pr. 255 to Pr .259)............................................................................... 211
3.20.3 Maintenance timer alarm (Pr.503, Pr.504)........................................................................................................ 213
3.20.4 Current average value monitor signal (Pr.555 to Pr.557) ................................................................................. 214
3.20.5 Free parameter (Pr.888, Pr.889) ....................................................................................................................... 216
3.21 Setting from the parameter unit, operation panel
3.21.1 PU display language selection (Pr.145) ............................................................................................................ 217
3.21.2 Operation panel frequency setting/key lock operation selection (Pr. 161) ....................................................... 217
3.21.3 Buzzer control (Pr. 990)..................................................................................................................................... 219
3.21.4 PU contrast adjustment (Pr.991) ....................................................................................................................... 219
3.22 Parameter clear
3.23 All parameter clear
3.24 Parameter copy
3.25 Parameter verification
52
118
124
125
136
142
156
184
210
217
220
221
222
223