NEC SL 1000 Programming Manual page 179

ISSUE 1.0
Item
No.
07
08
09
10
11
12
15
Programming Manual
Downloaded from www.Manualslib.com
Item
Time and Date Display 1 ~ 10 (SL1000)
Mode Type 1 = (12 hour) TUE 10 3 : 15 PM (SL1000)
Set how the Time and Type 2 = (12 hour) 3-10 TUE 3 : 15 (SL1000)
Date appear on display Type 3 = (12 hour) 10-3 TUE 3 : 15 (SL1000)
telephones. There are Type 4 = (12 hour) MAR 10 TUE 3 : 15 (SL1000)
eight display modes. Type 5 = (24 hour) TUE 10 3 15 : 15 (SL1000)
Type 6 = (24 hour) 3-10 TUE 15 : 15 (SL1000)
Type 7 = (24 hour) 10-3 TUE 15 : 15 (SL1000)
Type 8 = (24 hour) MAR 10 TUE 15 : 15
(SL1000)
Type 9 = (12 hour) 10 MAR TUE 3 : 15 (SL1000)
Type 10 = (24 hour) 10 MAR TUE 15 : 15
(SL1000)
1 ~ 8 (SL1100)
Type 1 = (12 hour) 10 MAR TUE 3 : 15 PM
(SL1100)
Type 2 = (12 hour) 3 : 15 PM MAR 10 TUE
(SL1100)
Type 3 = (12 hour) 3-10 TUE 3 : 15 PM (SL1100)
Type 4 = (12 hour) 3 : 15 PM TUE 10 MAR
(SL1100)
Type 5 = (24 hour) 10 MAR TUE 15 : 15
(SL1100)
Type 6 = (24 hour) 15 : 15 MAR 10 TUE
(SL1100)
Type 7 = (24 hour) 3-10 TUE 15 : 15 (SL1100)
Type 8 = (24 hour) 15 : 15 TUE 10 MAR
(SL1100)
LCD Display Holding 0 ~ 64800 seconds
Time
Disconnect Supervision 0 = Disable (Off)
Use this option to enable 1 = Enable (On)
or disable disconnect su-
pervision for the system
trunks.
Time Before Shifting to 0 = No Shift
Power-Saving Mode 1 = 1 minute
2 = 2 minutes
3 = 4 minutes
4 = 8 minutes
5 = 16 minutes
6 = 32 minutes
7 = 64 minutes
Handsfree Microphone 0 = Off
Control 1 = On
Use this option to control
the setting for Multiline
Terminal Handsfree micro-
phone after being discon-
nected and reconnected. If
set to 0, the microphone is
always off when the termi-
nal is reconnected. If set
to 1, the microphone re-
mains in the same state it
was in when the terminal
is reconnected.
Forced Intercom Ring 0 = Disable (Voice)
(ICM Call Type) 1 = Enable (Signal)
Use this option to enable
or disable Forced Inter-
com Ringing. If enabled,
incoming Intercom calls
normally ring. If disabled,
Intercom calls voice-
announce.
Caller ID Display Mode 0 = Name and Number (Both)
1 = Name
2 = Number
manuals search engine
Input Data Default
1 (SL1000)
3 (SL1100)
SL1000/SL1100
Related
Note
Program
5
1
0 15-02-18
1
1
0
2-157
Program
20