ABB ACH580 Series Installation, Operation And Maintenance Manual page 126

126
Complete ACH580 Drive Parameter List
GROUP 1
Actual values
1.01 Motor speed used
1.02 Motor speed estimated
1.03 Motor speed %
1.06 Output frequency
1.07 Motor current
Motor current % of motor
1.08
nom
Motor current % of drive
1.09
nom
1.10 Motor torque
1.11 DC voltage
1.13 Output voltage
1.14 Output power
Output power % of motor
1.15
nom
Output power % of drive
1.16
nom
1.17 Motor shaft power
1.18 Inverter GWh counter
1.19 Inverter MWh counter
1.20 Inverter kWh counter
1.24 Flux actual %
1.30 Nominal torque scale
1.31 Ambient temperature
1.50 Current hour kWh
1.51 Previous hour kWh
1.52 Current day kWh
1.53 Previous day kWh
1.54 Cumulative inverter energy
Inverter GWh counter
1.55
(resettable)
Inverter MWh counter
1.56
(resettable)
Inverter kWh counter
1.57
(resettable)
Cumulative inverter energy
1.58
(resettable)
1.61 Abs motor speed used
1.62 Abs motor speed %
1.63 Abs output frequency
1.64 Abs motor torque
1.65 Abs output power
Abs output power % motor
1.66
nom
Abs output power % drive
1.67
nom
1.68 Abs motor shaft power
1.102 Line current
1.104 Active current
1.106 Reactive current
1.108 Grid frequency
1.109 Grid voltage
1.110 Grid apparent power
1.112 Grid power
1.114 Grid reactive power
1.116 LSU cos Phi
1.164 LSU nominal power
GROUP 3
Input references
3.01 Panel reference
3.02 Panel reference remote
3.05 FB A reference 1
3.06 FB A reference 2
3.09 EFB reference 1
3.10 EFB reference 2
GROUP 4
Warnings and faults
4.01 Tripping fault
4.02 Active fault 2
4.03 Active fault 3
4.06 Active warning 1
4.07 Active warning 2
4.08 Active warning 3
4.11 Latest fault
4.12 2nd latest fault
4.13 3rd latest fault
4.16 Latest warning
4.17 2nd latest warning
4.18 3rd latest warning
4.40 Event word 1
4.41 Event word 1 bit 0 code
4.43 Event word 1 bit 1 code
4.45 Event word 1 bit 2 code
4.47 Event word 1 bit 3 code
4.49 Event word 1 bit 4 code
4.51 Event word 1 bit 5 code
ACH580-Parameter List
ACH580 Ultra-Low Harmonic Drives Installation, Operation and Maintenance Manual
4.53 Event word 1 bit 6 code
4.55 Event word 1 bit 7 code
4.57 Event word 1 bit 8 code
4.59 Event word 1 bit 9 code
4.61 Event word 1 bit 10 code
4.63 Event word 1 bit 11 code
4.65 Event word 1 bit 12 code
4.67 Event word 1 bit 13 code
4.69 Event word 1 bit 14 code
4.71 Event word 1 bit 15 code
GROUP 5
Diagnostics
5.01 On-time counter
5.02 Run-time counter
5.03 Hours run
5.04 Fan on-time counter
5.10 Control board temperature
5.11 Inverter temperature
5.22 Diagnostic word 3
5.111 Line converter temperature
5.121 MCB closing counter
GROUP 6
Control and status words
6.01 Main control word
6.11 Main status word
6.16 Drive status word 1
6.17 Drive status word 2
6.18 Start inhibit status word
6.19 Speed control status word
6.20 Constant speed status word
6.21 Drive status word 3
6.22 HVAC status word
6.30 MSW bit 11 selection
6.31 MSW bit 12 selection
6.32 MSW bit 13 selection
6.33 MSW bit 14 selection
6.36 LSU Status word
Internal state machine LSU
6.39
CW
6.116 LSU drive status word 1
6.118 LSU start inhibit status word
GROUP 7
System info
7.03 Drive rating id
7.04 Firmware name
7.05 Firmware version
7.06 Loading package name
7.07 Loading package version
7.11 Cpu usage
Customization package
7.25
name
Customization package
7.26
version
7.30 Adaptive program status
7.31 AP sequence state
7.106 LSU loading package name
LSU loading package
7.107
version
GROUP 10
Standard DI, RO
10.02 DI delayed status
10.03 DI force selection
10.04 DI forced data
10.21 RO status
10.22 RO force selection
10.23 RO forced data
10.24 RO1 source
10.25 RO1 ON delay
10.26 RO1 OFF delay
10.27 RO2 source
10.28 RO2 ON delay
10.29 RO2 OFF delay
10.30 RO3 source
10.31 RO3 ON delay
10.32 RO3 OFF delay
10.99 RO/DIO control word
10.101 RO1 toggle counter
10.102 RO2 toggle counter
10.103 RO3 toggle counter
GROUP 11
Standard DIO, FI, FO
11.21 DI5 configuration
11.38 Freq in 1 actual value
11.39 Freq in 1 scaled value
11.42 Freq in 1 min
11.43 Freq in 1 max
11.44 Freq in 1 at scaled min
11.45 Freq in 1 at scaled max
GROUP 12
Standard AI
12.02 AI force selection
12.03 AI supervision function
12.04 AI supervision selection
12.11 AI1 actual value
12.12 AI1 scaled value
12.13 AI1 forced value
12.15 AI1 unit selection
12.16 AI1 filter time
12.17 AI1 min
12.18 AI1 max
12.19 AI1 scaled at AI1 min
12.20 AI1 scaled at AI1 max
12.21 AI2 actual value
12.22 AI2 scaled value
12.23 AI2 forced value
12.25 AI2 unit selection
12.26 AI2 filter time
12.27 AI2 min
12.28 AI2 max
12.29 AI2 scaled at AI2 min
12.30 AI2 scaled at AI2 max
12.101 AI1 percent value
12.102 AI2 percent value
GROUP 13
Standard AO
13.02 AO force selection
13.11 AO1 actual value
13.12 AO1 source
13.13 AO1 forced value
13.15 AO1 unit selection
13.16 AO1 filter time
13.17 AO1 source min
13.18 AO1 source max
13.19 AO1 out at AO1 src min
13.20 AO1 out at AO1 src max
13.21 AO2 actual value
13.22 AO2 source
13.23 AO2 forced value
13.26 AO2 filter time
13.27 AO2 source min
13.28 AO2 source max
13.29 AO2 out at AO2 src min
13.30 AO2 out at AO2 src max
13.91 AO1 data storage
13.92 AO2 data storage
GROUP 15
I/O extension module
15.01 Extension module type
15.02 Detected extension module
15.03 DI status
15.04 RO/DO status
15.05 RO/DO force selection
15.06 RO/DO forced data
15.07 RO4 source
15.08 RO4 ON delay
15.09 RO4 OFF delay
15.10 RO5 source
15.11 RO5 ON delay
15.12 RO5 OFF delay
15.22 DO1 configuration
15.23 DO1 source
15.24 DO1 ON delay
15.25 DO1 OFF delay
15.32 Freq out 1 actual value
15.33 Freq out 1 source
15.34 Freq out 1 src min
15.35 Freq out 1 src max
15.36 Freq out 1 at src min
15.37 Freq out 1 at src max
GROUP 19
Operation mode
19.01 Actual operation mode
19.11 Ext1/Ext2 selection
19.18 HAND/OFF disable source
19.19 HAND/OFF disable action
GROUP 20
Start/stop/direction
20.01 Ext1 commands
20.02 Ext1 start trigger type
20.03 Ext1 in1 source
20.04 Ext1 in2 source
20.05 Ext1 in3 source
20.06 Ext2 commands
20.07 Ext2 start trigger type
20.08 Ext2 in1 source
20.09 Ext2 in2 source
20.10 Ext2 in3 source
20.21 Direction
20.40 Run permissive
20.41 Start interlock 1
20.42 Start interlock 2
20.43 Start interlock 3
20.44 Start interlock 4
20.45 Start interlock stop mode
GROUP 21
Start/stop mode
21.01 Start mode
21.02 Magnetization time
21.03 Stop mode
21.04 Emergency stop mode
21.05 Emergency stop source
21.06 Zero speed limit
21.07 Zero speed delay
21.08 DC current control
21.09 DC hold speed
21.10 DC current reference
21.11 Post magnetization time
21.14 Pre-heating input source
21.16 Pre-heating current
21.18 Auto restart time
21.19 Scalar start mode
21.21 DC hold frequency
21.22 Start delay
21.23 Smooth start
21.24 Smooth start current
21.25 Smooth start speed
21.26 Torque boost current
Speed compensated stop
21.30
mode
21.31 Speed comp stop delay
21.32 Speed comp stop threshold
21.34 Force auto restart
GROUP 22
Speed reference selection
22.01 Speed ref unlimited
22.11 Ext1 speed ref1
22.12 Ext1 speed ref2
22.13 Ext1 speed function
22.18 Ext2 speed ref1
22.19 Ext2 speed ref2
22.20 Ext2 speed function
22.21 Constant speed function
22.22 Constant speed sel1
22.23 Constant speed sel2
22.24 Constant speed sel3
22.26 Constant speed 1
22.27 Constant speed 2
22.28 Constant speed 3
22.29 Constant speed 4
22.30 Constant speed 5
22.31 Constant speed 6
22.32 Constant speed 7
22.41 Speed ref safe
22.51 Critical speed function
22.52 Critical speed 1 low
22.53 Critical speed 1 high
22.54 Critical speed 2 low
22.55 Critical speed 2 high
22.56 Critical speed 3 low
22.57 Critical speed 3 high
22.71 Motor potentiometer function
Motor potentiometer initial
22.72
value
Motor potentiometer up
22.73
source
Motor potentiometer down
22.74
source
Motor potentiometer ramp
22.75
time
Motor potentiometer min
22.76
value
Motor potentiometer max
22.77
value
22.80 Motor potentiometer ref act
22.86 Speed reference act 6
22.87 Speed reference act 7
GROUP 23
Speed reference ramp
23.01 Speed ref ramp input
23.02 Speed ref ramp output
23.11 Ramp set selection
23.12 Acceleration time 1
23.13 Deceleration time 1
23.14 Acceleration time 2