GE MiCOM P40 Agile Technical Manual page 371

Programmable Logic
MiCOM 40 Agile P442, P444
Ordinal English Text
262 T2
1095 T2 Timer Block
263 T3
1098 T3 Timer Block
264 T4
1099 T4 Timer Block
333 tBF1 Trip
334 tBF2 Trip
206 Test Mode Acq
369 Thermal Alarm
1092 Time Synch
830 to Timer in 1 to
845 Timer in 16
830 to Timer in 1 to
861 Timer in 16
862 to Timer in 1 to
893 Timer in 16
846 to Timer out 1 to
861 Timer out 16
314 TOC Start A
315 TOC Start B
316 TOC Start C
313 TOR Enable
1032 TPAR Enable
368 Trace Trig OK
1024 Trip LED
370 Trip Thermal
265 Tzp
1096 TZp Timer Block
Description
Distance time-delay in zone 2 tZ2 elapsed (1 = end of
timer)
Timer block T2 input
Distance time-delay in zone 3 tZ3elapsed (1 = end of
timer)
Timer block T3 input
Distance time-delay in zone 4 tZ4 elapsed (1 = end of
timer)
Timer block T4 input
Circuit Breaker failure on any trip, delayed by "CB Fail
1 Timer" (setting in "CB Fail" logic)
Circuit Breaker failure on any trip, delayed by "CB Fail
2 Timer" (setting in "CB Fail" logic)
Relays with IEC 61850 9-2 Ethernet board only with
software version up to D4.x - Any Logical Node is in
"Test Mode"
Alarm from Thermal Overload function picks up
External time synchronisation input
Hardware version K - PSL Input to Auxiliary Timer 1
to PSL Input to Auxiliary Timer 16
Hardware version J - PSL Input to Auxiliary Timer 1
to PSL Input to Auxiliary Timer 32
Hardware version J - PSL Output from Auxiliary Timer
1
to PSL Output from Auxiliary Timer 32
Hardware version K - PSL Ouput from Auxiliary Timer
1
PSL Ouput from Auxiliary Timer 16
Trip on Close start on phase A: indicates a trip order
on phase A has been issued by the SOTF level
detectors (Pickup time-delay = 20 ms)
Trip on Close start on phase B: indicates a trip order
on phase B has been issued by the SOTF level
detectors (Pickup time-delay = 20 ms)
Trip on Close start on phase C: indicates a trip order
on phase C has been issued by the SOTF level
detectors (Pickup time-delay = 20 ms)
Trip On Reclose enable: indicates the TOR logic is
activated in the relay
Set to 1= 500 ms pulse initiated by:
'I A/R Reclaim' (internal) OR 'A/R reclaim' (External
Input)
OR Any pole open for more than 200 ms
Reset 500 ms after Any pole dead stops
Enable internal three pole autorecloser
Set with Opto input (if linked by PSL) is energized (>
1s).
At 1: 3P AR internal is enabled in the AR logic
At 0: AR 3P internal is disabled (even if set in MiCOM
S1 Agile). 1P cycle available if SPAR =1
Triggering trace has operated correctly
LED trip
Trip with Thermal Overload fucntion (timer issued)
Distance time-delay in zone p tZp elapsed (1 = end of
timer)
Timer block TZp input
P44x/EN PL/Hb6
(PL) 6-51
Source
PSL (OUT)
Distance
PSL
PSL (OUT)
Distance
PSL
PSL (OUT)
Distance
PSL
PSL (OUT)
Breaker
failure
PSL (OUT)
Breaker
failure
PSL (OUT)
PSL (OUT)
PSL(IN)
Auxiliary
Timer
Auxiliary
Timer
Auxiliary
Timer
Auxiliary
Timer
PSL (OUT)
SOTF
PSL (OUT)
SOTF
PSL (OUT)
SOTF
PSL (OUT)
TOR
PSL (IN)
Autorecloser
PSL (OUT)
PSL (OUT)
PSL (OUT)
Distance
PSL