Ff2 0: Analog Trunks (Co); Defaults For Ff2: Trunks - Panasonic DBS-576 Technical Manual

Section 400-Programming

Defaults for FF2: TRUNKS

Introduction
FF Key Address

FF2 0: Analog Trunks (CO)

FF2 0 BSSC 00 Hold (0-576) Hold
0
System FF2 0 BSSC 01 00 Hold (0-3) Hold
Configuration
FF2 0 BSSC 01 01 Hold (0 or 1) Hold
FF2 0 BSSC 01 02 Hold (0 or 1) Hold
FF1
FF2 0 BSSC 01 03 Hold (0 or 1) Hold
System
FF2 0 BSSC 01 04 Hold (0 or 1) Hold
FF2 0 BSSC 01 05 Hold (0 or 1) Hold
FF2 0 BSSC 01 06 Hold
FF2
FF2 0 BSSC 01 07 Hold
FF2 0 BSSC 01 08 Hold
Trunks
FF2 0 BSSC 01 09 Hold (0 or 1) Hold
FF2 0 BSSC 01 10 Hold (0 or 1) Hold
FF2 0 BSSC 01 11 Hold (0-6) Hold
FF3
FF2 0 BSSC 01 12 Hold (0-12) Hold
Extensions
FF2 0 BSSC 01 13 Hold (0-2) Hold
FF2 0 BSSC 01 14 Hold (0-2) Hold
FF2 0 BSSC 01 15 Hold (0-3) Hold
FF4
FF2 0 BSSC 01 16 Hold (0-3) Hold
FF-/Soft Keys
FF2 0 BSSC 01 17 Hold (0-3) Hold
FF2 0 BSSC 01 18 Hold
FF2 0 BSSC 01 19 Hold (0-3) Hold
FF5
FF2 0 BSSC 02 00 Hold (0 or 1) Hold
Groups
FF2 0 BSSC 02 01 Hold (0 or 1) Hold
FF2 0 BSSC 02 02 Hold (0 or 1) Hold
FF2 0 BSSC 02 03 Hold (0 or 1) Hold
FF6
FF2 0 BSSC 02 04 Hold (0 or 1) Hold
TRS/ARS
FF2 0 BSSC 02 05 Hold (0 or 1) Hold
FF2 0 BSSC 02 06 Hold (0 or 1) Hold
FF2 0 BSSC 02 07 Hold (0 or 1) Hold
FF7
FF2 0 BSSC 02 08 Hold (0 or 1) Hold
Applications
FF2 0 BSSC 02 09 Hold (0 or 1) Hold
FF2 0 BSSC 02 10 Hold (0 or 1) Hold
FF2 0 BSSC 02 11 Hold (0 or 1) Hold
FF8
FF2 0 BSSC 02 12 Hold (0 or 1) Hold
FF2 0 BSSC 02 13 Hold (0 or 1) Hold
Maintenance
FF2 0 BSSC 02 14 Hold (0 or 1) Hold
FF2 0 BSSC 02 15 Hold (0 or 1) Hold
FF2 0 BSSC 02 16 Hold (0 or 1) Hold
FF2 0 BSSC 02 17 Hold (0 or 1) Hold
Appendix A
FF2 0 BSSC 02 18 Hold
FF2 0 BSSC 02 19 Hold
FF2 0 BSSC 02 20 Hold
Appendix B
576-13-400
Topic
Trunk Number Assignment
Trunk Signal Type
Loop Detect
Disconnect Detect
Dial Pulse Minimum Pause
Ground Start Ring Type
DID Ring Detect Timer
Not Used
Reverse Answer Signal Control
Caller ID
Ring Frequency
Ring Pattern
DTMF On/Off Pattern During Talk
DTMF On/Off Pattern for Outgoing Dialing 0 (Pattern #1)
Disconnect Supervision Timer
Guard Timer for Outbound Calls
Inbound Ground Detect Timer
Not Used
Ring Interval for Abandoned Calls
DTMF/Dial Pulse Dialing
Flash Pattern
Dial Tone Detection
Call Duration
Trunk Connection Type (CO/PBX)
Auto-Repeat Dial
DTMF After Answer (Link Control)
CO Dial Tone Simulation
Caller ID Ring Control
SMDR for Outbound Calls
SMDR for Inbound Calls
Flash Key Operation
Long Talk Alarm
Alarm Ringing
Slide Ringing
DTMF Conversion (Outbound Calls)
DTMF Conversion (Inbound Calls)
Indirect LCR
Not Used
DBS 576 (USA) issued 05/20/98
Introduction to DBS 576 Programming
Default
--
LS & LS/GS: 0
GS: 1
DID Immed.: 2
1 (Enabled)
0 (Enabled)
0 (625ms)
0 (Enabled)
0 (32ms)
--
1 (Disabled)
0 (Disabled)
1 (400/562Hz)
0 (synch. w/CO)
1 (Pattern #2)
0 (281ms)
LS/GS:
0 (96ms)
DID:
0 (.5 seconds)
0 (1 second)
--
0 (5 seconds)
1 (DTMF)
0 (Pattern #1)
1 (Enabled)
1 (Use system
timer)
0 (CO)
1 (Allowed)
0 (Allowed)
0 (Disabled)
0 (Wait)
1 (Include)
0 (Exclude)
0 (flash to CO)
0 (Disabled)
0 (Disabled)
0 (Disabled)
1 (Enabled)
1 (Enabled)
0 (Disabled)
--
Introduction
Page
2-7
2-7
0
2-8 System
Configuration
2-8
2-9
FF1
2-9
System
2-10
2-10
2-11
FF2
Trunks
2-11
2-12
2-12
FF3
2-13
Extensions
2-14
2-14
2-15
FF4
2-15
FF-/Soft Keys
2-16
2-16
2-17
FF5
2-17
Groups
2-18
2-18
2-19
FF6
2-19
TRS/ARS
2-20
2-20
2-21
FF7
2-21
Applications
2-22
2-22
2-23
FF8
2-23
2-24
Maintenance
2-25
2-26
2-26
2-27
Appendix A
2-27
Appendix B
Intro-29