Panasonic DBS-576 Technical Manual page 87

Section 400-Programming
(all CPCs - Version 1.3 and higher)
Introduction
Auto Answer will apply (the ability to answer the incoming call simply by picking up the handset),
as long as the BLF key is enabled for ringing in the Trunk FF-Key addresses in FF4. If the Trunk
FF-Key addresses are left at default 0=Do not ring, the user must press the BLF key to answer the
incoming call.
0
System
If the phone is ringing for the BLF call, the phone's display will read "INCM" and the BLF Ext.No.
Configuration
or Name.
If a BLF call is answered and in progress, the BLF key will start blinking green if it receives a
second incoming call. Press the BLF key to pick up the second call (and disconnect from the first).
FF1
System
Related Programming:
Trunk FF-Key: Day1 Ringing (pg. 4-11)
Trunk FF-Key: Day2 Ringing (pg. 4-12)
FF2
Trunk FF-Key: Night Ringing (pg. 4-12)
Trunks
Trunk FF-Key: No-Ring Auto Answer (pg. 4-13)
DSS Trunk FF-Key: Day1 Ringing (pg. 4-16)
DSS Trunk FF-Key: Day2 Ringing (pg. 4-17)
DSS Trunk FF-Key: Night Ringing (pg. 4-17)
FF3
DSS Trunk FF-Key: No-Ring Auto Answer (pg. 4-18)
Extensions
FF4
Day/Night Mode Assignment
FF-/Soft Keys
(all CPCs) - Version 1.0 or higher
Set method of Day/Night Mode assignment.
FF5
Groups
FF6
TRS/ARS
Notes:
FF7
If set to "0" (system-wide), Auto-Mode switching can be used.
Applications
If set to "1" (per MCO Tenant Group), each MCO Tenant Group can have its own Day and Night
modes, but mode switching must be performed manually -- Auto-Mode switching is not allowed.
FF8
Related Programming:
Maintenance
Extension COS: System Mode Switch (pg. 1-55)
Day1/2/Night Ring Type/Destination for trunks -- see Chapter 2: Trunk Programming
FF8 1 07: Special Days/Times (pg. 8-53)
System Mode Display (pg. 3-17)
Appendix A
Appendix B
576-13-400
Assuming the above address is left at default 1=Enable ...
FF4 0 BSSC 1 (01-32) Hold CONF Holdx2 (0 or 1) Hold
FF4 0 BSSC 1 (01-32) Hold CONF Holdx3 (0 or 1) Hold
FF4 0 BSSC 1 (01-32) Hold CONF Holdx4 (0 or 1) Hold
FF4 1 BSSC 1 (01-72) Hold CONF Holdx2 (0 or 1) Hold
FF4 1 BSSC 1 (01-72) Hold CONF Holdx3 (0 or 1) Hold
FF4 1 BSSC 1 (01-72) Hold CONF Holdx4 (0 or 1) Hold
FF1 0 02 0007 Hold (0 or 1) Hold
0=Day/Night Mode is set system-wide. (default)
1=Day/Night Mode is set for each MCO Tenant Group.
FF3 0 BSSC 04 16 Hold (0 or 1) Hold
DBS 576 (USA) issued 05/20/98
FF4 0 BSSC 1 (01-32) Hold CONF Holdx5 (0 or 1) Hold
FF4 1 BSSC 1 (01-72) Hold CONF Holdx5 (0 or 1) Hold
FF1 0 03 (00-15) 26 Hold (0 or 1) Hold
FF1: System Programming
%
0)9 2! 
Page 1-25
Introduction
0
System
Configuration
FF1
System
FF2
Trunks
FF3
Extensions
FF4
FF-/Soft Keys
FF5
Groups
FF6
TRS/ARS
FF7
Applications
FF8
Maintenance
Appendix A
Appendix B