Toshiba ACE-tronics G9 ASD Installation And Operation Manual page 252

Table 10. My Function Input Setting (Input Function Target) Assignments, and Parameter/Input Setting
Numbers for the BRAKE-A/B/C, OUT1, OUT2, OUT3–OUT6, and R1–R4 Terminals.
Discrete Output Terminal Assignment Selections (Positive Logic)
Input Param.
Setting Setting
1000 0 Lower-Limit Frequency
1002 2 Upper-Limit Frequency
1004 4 Low Speed Signal
1006 6 Acceleration/Deceleration Completion
1008 8 Speed Reach Signal
1010 10 Failure BRAKE (All Trips)
1012 12 Failure BRAKE (Except EF, OCL, EPHO, OL2)
1014 14 Over-Current (OC) Alarm
1016 16 ASD Overload (OL1) Alarm
1018 18 Motor Overload (OL2) Alarm
1020 20 Overheat Alarm
1022 22 Over-Voltage Alarm
1024 24 Main Circuit (MOFF) Under-Voltage Alarm
1026 26 Low-Current Alarm
1028 28 Over-Torque Alarm
1030 30 DBR Overload Alarm
1032 32 Emergency Off Active
1034 34 Retry Active
1036 36 Pattern Operation Switching Output
1038 38 PID Deviation Limit
1040 40 Run/Stop
Serious Failure (OCA, OCL, EF, Phase Failure,
1042 42
etc.)
1044 44 Light Failure (OL, OC1, 2, 3, OP)
1046 46 Commercial Power/ASD Switching Output 1
1048 48 Commercial Power/ASD Switching Output 2
1050 50 Cooling Fan On/Off
1052 52 Jogging Operation Active (Jog Run Active)
1054 54 Panel/Terminal (Board) Operation Switching
1056 56 Bearing Greaser Run-Time Alarm
ProfiBus/DeviceNet/CC-Link Communication
1058 58
Error
1060 60 Forward/Reverse Switching
1062 62 Ready for Operation 1
1064 64 Ready for Operation 2
1068 68 Brake Release (BR)
1070 70 Alarm Status Active
1072 72 Forward Speed Limit (Torque Control)
242
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
Function
Input Param.
Setting Setting
1074 74 Reverse Speed Limit (Torque Control)
1076 76 ASD Healthy Output
1078 78 RS485 Communication Error
1080 80 Error Code Output 1
1082 82 Error Code Output 2
1084 84 Error Code Output 3
1086 86 Error Code Output 4
1088 88 Error Code Output 5
1090 90 Error Code Output 6
1092 92 Specified Data Output 1
1094 94 Specified Data Output 2
1096 96 Specified Data Output 3
1098 98 Specified Data Output 4
1100 100 Specified Data Output 5
1102 102 Specified Data Output 6
1104 104 Specified Data Output 7
1106 106 Switch Out Of Sequence
1108 108 Heavy Load
1110 110 Positive Torque Limit
1112 112 Negative Torque Limit
1114 114 External Rush Suppression Relay Activated
1118 118 Completion of Stop Positioning
1120 120 L-STOP
1122 122 Power Failure Synchronized Operation
1124 124 Traverse Active
1126 126 Traverse Deceleration Active
1128 128 Part Replaceme nt Alarm
1130 130 Over-Torque Alarm
1132 132 Frequency Command ½ Selection
1134 134 Failure BRAKE (Non-Emergency Off)
1136 136 External Fault
1138 138 Drooping Fault
1140 140 Run Before Ready
1142 142 Slow-Speed Limit Switch
1144 144 Stop Limit-Switch Forward
1146 146 Slow-Speed Limit Switch
ACE-tronics G9 ASD Installation and Operation Manual
Function