Mitsubishi Electric MELDASMAGIC64 Connection Manual page 12

7. Remote I/O Unit Connection ..............................................................................................
7.1 Outline of Remote I/O Unit .............................................................................................
7.2 Names of Each Remote I/O Unit Section .......................................................................
7.3 Connection of Remote I/O Power...................................................................................
7.4 Outline of Digital Signal Input Circuit ..............................................................................
7.5 Outline of Digital Signal Output Circuit ...........................................................................
7.6 Outline of Analog Signal Output Circuit ..........................................................................
7.7 Outline of Analog Signal Input Circuit.............................................................................
7.8 Connection of FCUA-DX10*/13*/14* Unit and Machine Control Signal ..........................
7.9 Connection of FCUA-DX11* Unit and Machine Control Signal.......................................
7.10 Connection of FCUA-DX12* Unit and Machine Control Signal.....................................
7.11 Connection of FCUA-DX13* Unit and Handle ..............................................................
7.12 Outline of FCUA-DX13* Unit Pulse Input Circuit ..........................................................
7.13 Connection of FCUA-DX14* Unit and Analog Input/Output Signal ...............................
7.14 Setting of Channel No. when Using Multiple Remote I/O Units....................................
7.15 Remote I/O Unit Input/Output Signal Cables................................................................
Appendix 1 Outline Drawings ................................................................................................
Appendix 1.1 ISA NC Card Outline Drawing (HR621) .......................................................
Appendix 1.2 ISA NC Card Outline Drawing (HR623) .......................................................
Appendix 1.3 PCI NC Card Outline Drawing (FCU6-HR655) ............................................
Appendix 1.4 Base I/O Unit Outline Drawing .....................................................................
Appendix 1.5 Relay Card (independent installation) Outline Drawing ...............................
Appendix 1.6 Base I/O Unit + Relay Card (add-on) Outline Drawing.................................
Appendix 1.7 Remote I/O Unit Outline Drawing.................................................................
Appendix 1.8 Manual Pulse Generator (HD60) Outline Drawing .......................................
Appendix 1.9 Spindle Encoder (OSE-1024-3-15-68) Outline Drawing...............................
Appendix 1.10 Grounding Plate and Clamp Fitting Outline Drawings..................................
Appendix 2 Cable Manufacturing Drawings .........................................................................
Appendix 2.1 SH21 cable (Servo drive unit) ......................................................................
Appendix 2.2 SH41 cable (Remote I/O unit)......................................................................
Appendix 2.3 R031 cable (Analog signal input/output) ......................................................
Appendix 2.4 R041 cable (Manual pulse generator)..........................................................
Appendix 2.5 R042 cable (Manual pulse generator)..........................................................
Appendix 2.6 R211 cable (Remote I/O unit) .....................................................................
Appendix 2.7 R220 cable (+24VDC input).........................................................................
Appendix 2.8 R300 cable (Machine input/output) ..............................................................
Appendix 2.9 R301 cable (Machine input/output) ..............................................................
Appendix 2.10 F010 cable (NC Card)..................................................................................
Appendix 2.11 F011 cable (NC Card) ..................................................................................
Appendix 2.12 F020 cable (Manual pulse generator) ........................................................
Appendix 2.13 F021 cable (Manual pulse generator) ........................................................
Appendix 2.14 F022 cable (Manual pulse generator) ........................................................
Appendix 2.15 F040 cable (Spindle encoder) ......................................................................
Appendix 2.16 F041 cable (Spindle encoder) ......................................................................
Appendix 2.17 F070 cable (+24VDC input) .........................................................................
Appendix 2.18 F390 cable (RS232C) ..................................................................................
Appendix 2.19 ENC-SP1 cable (Spindle drive unit) ........................................................... 100
Appendix 2.20 Table of Connector Sets ............................................................................. 101
Appendix 3 Parts for EMC Measures..................................................................................... 102
Appendix 3.1 Shield Clamp Fitting..................................................................................... 102
Appendix 3.2 Ferrite Core.................................................................................................. 103
Appendix 3.3 Surge Protector............................................................................................ 104
Appendix 3.4 Selection of Stabilized Power Supply........................................................... 107
xi
51
51
52
53
54
56
57
58
59
61
63
65
66
67
68
70
71
71
71
72
73
74
75
76
77
78
79
80
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99