Siemens SIMATIC S5 Manual page 324

Index
O
OFF, operating mode of IM 308-C, 11-7
offline, Glossary-7
OLM, 1-16
online, Glossary-7
operating system datum, S5-95U, 12-4
operating system file, 3-11
definition, 8-2
operating system version of the IM 308-C, 3-12
operation of the ET 200, general rules and regu-
lations, 5-3
OPs as DP slaves, 1-3
optical link module, 1-16
order numbers, F-1
other-vendor masters, 8-20
overview diagnostics, 9-12, 10-4
definition, 10-5
in the STEP 5 application program, inter-
preting, 10-5
structure, 9-13, 10-5
overvoltage, definition, D-2
overvoltage diverter, Glossary-7
P
page addressing, definition, 9-7
parameterization, Glossary-7
parameterization master, Glossary-7
parameterization software COM ET 200
Windows, 1-4
parameterization with COM ET 200 Windows,
procedure, 2-6
parameterize, slave parameters, 8-15
parameterizing, Glossary-7
parameterizing a configuration with
COM ET 200 Windows, 8-5
parameterizing an ET 200 distributed I/O sys-
tem, 8-5
planning the layout, procedure, 2-2
PLC cycle, 4-7
pollutant concentration, A-4
potential differences, avoiding, 5-8
potential equalization, 5-8
power failure, handling a power failure, 11-15
power restored in the S5-95U, 12-7
power supply, switching on, 11-5
powerfail in the S5-95U, 12-7
power-up delay, host parameters, 8-10
power-up of the S5-95U on the bus, 12-3
preconditions, 12-3
power-up phase, C-22
Index-6
P-page addressing, 9-4
definition and restrictions, 9-8
preconditions, for using COM ET 200 Win-
dows, 7-2
preconditions for the S5-95U as DP master, 7-2
preconditions for use as DP master, 7-2
printing, 8-29
printing system documentation, example, 7-13
procedure
from planning to initial operation of the ET
200, 2-1
initial operation of the ET 200, 2-9
parameterization with COM ET 200 Win-
dows, 2-6
planning the layout, 2-2
STEP 5 application program writing, 2-8
structuring the ET 200, 2-3
what to consider before parameterization
with COM ET 200 Windows, 2-4
process image, Glossary-8
PROFIBUS, Glossary-8
PROFIBUS-DP, Glossary-8
program file
creating, 8-3
definition, 8-2
opening, 8-3
programmable controller S5-95U with SINEC
L2-DP interface, 1-12
programming units, power supply, 5-14
protection class, A-6
Q
Q-page addressing, 9-4
definition and restrictions, 9-8
R
RC element, 5-13
reaction time, Glossary-8
calculating, C-11
importance, C-2, C-5
in ET 200, C-2, C-5
of ET 200, 1-3
t , C-4
cons
t , C-8
DP
t , C-7
inter
t , C-3, C-6
prog
t , definition, C-17
R
t , C-9
slave
redundancy, Glossary-8
ET 200 Distributed I/O System
EWA 4NEB 780 6000-02a