Mitsubishi Electric FR-E700EX Instruction Manual page 320

G
Gain adjustment of position control (Pr.422, Pr.423, Pr.427,
Pr.427, Pr.446, Pr.463, Pr.698, Pr.877)..............................92
H
Harmonic suppression guideline in Japan..............................39
Heatsink overheat (E.FIN).......................................................274
Heatsink overheat prealarm (FIN signal) ..................... 144
High-speed operation command (RH signal).............. 117
Home position return completed (ZP signal)........................144
Home position return failure warning (ZA signal) ................144
Home position return setting error (HP1)..............................270
Home position return uncompleted (HP2) ............................270
Home position return under position control
(Pr.110, Pr.111, Pr.453, Pr.455, Pr.508, Pr.509, Pr.532 to
Pr.534) ..................................................................................... 104
I
Initial settings and specifications of RS-485 communication
(Pr.117 to Pr.120, Pr.123, Pr.124, Pr.549)......................... 204
Initiating a fault (Pr.997) ..........................................................252
In-position (Y36 signal) ............................................................144
Input phase loss (E.ILF) ................................................. 166
Input terminal function selection (Pr.178 to Pr.184)............138
Input terminal status.................................................................155
Input/output phase loss protection selection
(Pr.251, Pr.872) ...................................................................... 166
Inrush current limit circuit fault (E.IOH) .................................277
Insulation resistance test using megger ...............................299
Internal board fault (E.PE2) ....................................................276
J
Jog operation
(Pr.15, Pr.16, JOG signal, JOG2 signal) ............................ 119
JOG operation selection (JOG signal) ..................................119
JOG operation selection2 (JOG2 signal) ..................... 119
L
Leakage currents and countermeasures ................................34
Life alarm (Y90 signal)............................................ 144
Loss of synchronism detection (E.SOT) ...............................275
Low-speed operation command (RL signal) ............... 117
M
Magnitude of speed change setting (Pr.295) .......................259
Maintenance signal output (MT).................................... 248
Maintenance timer alarm (Pr.503, Pr.504) ...........................248
Maintenance timer signal (Y95 signal) ......................... 144
Maximum/minimum setting (Pr.1, Pr.2).................................115
Measurement of converter output voltage (across terminals
P/+ and N/-) ...........................................................................298
Measurement of currents ........................................................298
Measurement of drive unit input power factor......................298
Measurement of drive unit output frequency........................299
Measurement of powers..........................................................297
Measurement of voltages and use of PT ..............................297
Middle-speed operation command (RM signal).......... 117
Mitsubishi inverter protocol
(computer link communication) ............................................ 209
Modbus-RTU communication specifications (Pr.117, Pr.118,
Pr.120, Pr.122, Pr.343, Pr.502, Pr.549)............................222
Monitor display selection of DU/PU and terminal FM/AM
318
(Pr.52, Pr.54, Pr.158, Pr.170, Pr.171, Pr.268, Pr.430,
Pr.563, Pr.564) ..................................................................... 155
Motor load factor ...................................................................... 155
Motor overheat protection (Electronic thermal O/L relay)
(Pr.9) ...................................................................................... 130
Motor overload trip (electronic thermal relay function)
(E.THM) ......................................................................... 130
Motor starting speed (Pr.13)................................................... 128
274
,
Motor thermal relay load factor .............................................. 155
138
,
N
Names and functions of the operation panel ......................... 48
Notch filter (Pr.862, Pr.863, Pr.871)........................................ 85
O
Operation by multi-speed operation (Pr.4 to Pr.6, Pr.24 to
Pr.27, Pr.232 to Pr.239) ...................................................... 117
Operation mode at power-ON (Pr.79, Pr.340)..................... 194
Operation mode selection (Pr.79).......................................... 186
Operation panel lock (Hold)............................................256
Operation selection at communication error occurrence
(Pr.121, Pr.122, Pr.502) ...................................................... 205
Option fault (E.1) ...................................................................... 276
274
,
Option fault (E.OPT) ................................................................ 275
Outline of position control ......................................................... 88
Outline of speed control ............................................................ 78
Outline of the PM sensorless vector control .......................... 73
Output current...................................................................155
Output current detection (Y12 signal) ...........................144
Output current detection function (Y12 signal, Y13 signal,
Pr.150 to Pr.153) .................................................................. 150
Output current peak value ..............................................155
Output phase loss (E.LF) ................................................166
Output power ............................................................................ 155
Output side earth (ground) fault overcurrent (E.GF) ..166
Output stop (MRS signal)................................................138
138
,
Output terminal function selection (Pr.190 to Pr.192) ........ 144
Output terminal status ............................................................. 155
Output voltage .......................................................................... 155
Overcurrent trip during acceleration (E.OC1) ...................... 272
, 244 , 245
Overcurrent trip during constant speed (E.OC2) ................ 272
Overcurrent trip during deceleration or stop (E.OC3) ........ 272
138
,
Overload alarm (OL signal) ............................................111
Overspeed occurrence (E.OS)............................................... 278
P
270
,
Parameter list.............................................................................. 52
Parameter storage device fault
, 248
(control circuit board) (E.PE)................................................ 276
Parameter write disable selection (Pr.77) ............................ 181
Parameter write error (Er1 to Er4)......................................... 268
Password function (Pr.296, Pr.297) ...................................... 183
Password locked (LOCd) ........................................................ 268
Periodic inspection................................................................... 288
PID control (Speed control) (Pr.127 to Pr.134) ................... 235
PID control valid terminal (X14 signal)..........................138
PID deviation.....................................................................155
138
,
PID forward/reverse rotation output (RL signal)..........144
PID lower limit (FDN signal) ...........................................144
PID measured value ........................................................155
PID set point......................................................................155
PID upper limit (FUP signal)...........................................144
Position command creating (PBSY signal) .......................... 144
, 273
268
,
, 161
, 150
161
,
, 275
, 275
140
,
144
,
, 235
, 235
235
,
235
,
235
,
, 235
, 235