Panel Display Process Variables - ABB ACS550-01 User Manual

112
Group 34: Panel Display Process Variables
This group defines the content for control panel display (middle area), when the
control panel is in the output mode.
Code Description
3401 SIGNAL1 PARAM
Selects the first parameter (by number) displayed on the control panel.
• Definitions in this group define display content when the control panel is in
the control mode.
• Any Group 01 parameter number can be selected.
• Using the following parameters, the display value can be scaled, converted
to convenient units, and/or displayed as a bar graph.
• The figure identifies selections made by parameters in this group.
100 = not selected – First parameter not displayed.
101...199 = Displays parameter 0101...0199. If parameter does not exist, the display shows "n.a."
3402 SIGNAL1 MIN
Defines the minimum expected value for the first display parameter.
Use parameters 3402, 3403, 3406, and 3407, for example to convert
a Group 01 parameter, such as 0102
conveyor driven by the motor (in ft/min). For such a conversion, the
source values in the figure are the min. and max. motor speed, and
the display values are the corresponding min. and max. conveyor
speed. Use parameter 3405 to select the proper units for the display.
Note! Selecting units does not convert values.
3403 SIGNAL1 MAX
Defines the maximum expected value for the first display parameter.
3404 OUTPUT1 DSP FORM
Defines the decimal point location for the first display parameter.
1...7 – Defines the decimal point location.
• Enter the number of digits desired to the right of the decimal
point.
• See table for example using pi (3.14159).
8 = – Specifies a bar meter display.
BAR METER
9 = – Decimal point location and units of measure are
DIRECT
identical to the source signal. See Group 01 parameter listing in
"Complete Parameter List" for resolution (which indicates the
decimal point location) and the units of measure.
3405 OUTPUT1 UNIT
Selects the units used with the first display parameter.
0 = 9 = °C
NOT SEL
1 = A 10 = lb ft
2 = V 11 = mA
3 = Hz 12 = mV
4 = % 13 = kW
5 = s 14 = W
6 = h 15 = kWh
7 = rpm 16 = °F
8 = kh 17 = hp
117 = %ref 119 = %dev
118 = %act 120 = %LD
3406 OUTPUT1 MIN
Sets the minimum value displayed for the first display parameter.
3407 OUTPUT1 MAX
Sets the maximum value displayed for the first display parameter.
Start-Up
(in rpm) to the speed of a
SPEED
18 = MWh 27 = ft
19 = m/s 28 = MGD
3
20 = m /h 29 = inHg
3
21 = dm /s 30 = FPM
22 = bar 31 = kb/s
23 = kPa 32 = kHz
24 = GPM 33 = Ohm
25 = PSI 34 = ppm
26 = CFM 35 = pps
121 = % SP 123 = Iout
122 = %FBK 124 = Vout
P 0137
P 0138
P 0139
Display
Value
P 3407
P 3406
3404 Value
0
1
2
3
4
5
6
7
36 = l/s 45 = Pa
37 = l/min 46 = GPS
38 = l/h 47 = gal/s
3
39 = m /s 48 = gal/m
3
40 = m /m 49 = gal/h
3
41 = kg/s 50 = ft /s
3
42 = kg/m 51 = ft /m
3
43 = kg/h 52 = ft /h
44 = mbar 53 = lb/s
125 = Fout 127 = Vdc
126 = Tout
ACS550 User's Manual
P 3404 P 3405
P3402 P 3403
Source Value
Display Range
+ 3 -32768...+32767
(Signed)
+ 3.1
+ 3.14
+ 3.142
3 0...65535
(Unsigned)
3.1
3.14
3.142
54 = lb/m 63 = Mrev
55 = lb/h 64 = d
56 = FPS 65 = inWC
57 = ft/s 66 = m/min
58 = inH O
2
59 = in wg
60 = ft wg
61 = lbsi
62 = ms