Relay Outputs - ABB ACS550-01 User Manual

82
Group 14: Relay Outputs
This group defines the condition that activates each of the relay outputs.
Code Description
1401 RELAY OUTPUT 1
Defines the event or condition that activates relay 1 – what relay output 1 means.
0 = – Relay is not used and is de-energized.
NOT SEL
1 = – Energize relay when drive is ready to function. Requires:
READY
• Run enable signal present.
• No faults exist.
• Supply voltage is within range.
• Emergency Stop command is not on.
2 = – Energize relay when the drive is running.
RUN
3 = (-1) – Energize relay when power is applied. De-energizes when a fault occurs.
FAULT
4 = – Energize relay when a fault is active.
FAULT
5 = – Energize relay when an alarm is active.
ALARM
6 = – Energize relay when motor rotates in reverse direction.
REVERSED
7 = – Energize relay when drive receives a start command (even if Run Enable signal is not present). De-
STARTED
energized relay when drive receives a stop command or a fault occurs.
8= 1 – Energize relay when first supervised parameter (3201) exceeds the limit (3203).
SUPRV OVER
• See "Group 32: Supervision" starting on page 109.
9 = 1 – Energize relay when first supervised parameter (3201) drops below the limit (3202).
SUPRV UNDER
• See "Group 32: Supervision" starting on page 109.
10 = 2 – Energize relay when second supervised parameter (3204) exceeds the limit (3206).
SUPRV OVER
• See "Group 32: Supervision" starting on page 109.
11 = 2
SUPRV UNDER
• See "Group 32: Supervision" starting on page 109.
12 = 3 – Energize relay when second supervised parameter (3207) exceeds the limit (3209).
SUPRV OVER
• See "Group 32: Supervision" starting on page 109.
13 = 3
SUPRV UNDER
• See "Group 32: Supervision" starting on page 109.
14 = – Energize relay when the output frequency is equal to the reference frequency.
AT SET POINT
15 = ( ) – Energize relay when the drive is in a fault condition and will reset after the programmed auto-reset
FAULT RST
delay.
• See parameter 3103 delay time.
16 = / – Energize relay when fault or alarm occurs.
FLT ALARM
17 = – Energize relay when external control is selected.
EXT CTRL
18 = 2 – Energize relay when
REF SEL
19 = – Energize relay when a constant speed is selected.
CONST FREQ
20 = – Energize relay when reference or active control place is lost.
REF LOSS
21 =
OVERCURRENT
22 =
OVERVOLTAGE
23 = – Energize relay when a drive overtemperature alarm or fault occurs.
DRIVE TEMP
24 =
UNDERVOLTAGE
25 = 1 – Energize relay when
AI LOSS
26 = 2 – Energize relay when
AI LOSS
27 = – Energize relay when a motor overtemperature alarm or fault occurs.
MOTOR TEMP
28 = – Energize relay when a stall alarm or fault exists.
STALL
29 = – Energize relay when an underload alarm or fault occurs.
UNDERLOAD
30 = – Energize relay when the PID sleep function is active.
PID SLEEP
31 = – Use relay to start/stop motor in PFC control (See Group 81: PFC Control).
PFC
• Use this option only when PFC control is used.
• Selection activated / deactivated when drive is not running.
32 = – Energize relay when PFC autochange operation is performed.
AUTOCHANGE
• Use this option only when PFC control is used.
33 = – Energize relay when the motor is magnetized and able to supply nominal torque (motor has
FLUX READY
reached nominal magnetizing).
34 = 2 – Energize relay when User Parameter Set 2 is active.
USER S
Start-Up
– Energize relay when second supervised parameter (3204) drops below the limit (3205).
– Energize relay when second supervised parameter (3207) drops below the limit (3208).
2 is selected.
EXT
– Energize relay when an overcurrent alarm or fault occurs.
– Energize relay when an overvoltage alarm or fault occurs.
– Energize relay when an undervoltage alarm or fault occurs.
1 signal is lost.
AI
2 signal is lost.
AI
ACS550 User's Manual