ABB ACS550-01 User Manual page 205

ACS550 User's Manual
Faults that indicate conflicts in the parameter settings are listed below.
Fault
Code
1000
1001
1003
1004
1005
1006
1007
1008
1009
1012
1013
1014
Fault Name In
Panel
Parameter values are inconsistent. Check for any of the following:
PAR HZRPM
• 2001
MINIMUM SPEED
• 2007
MINIMUM FREQ
• 2001
MINIMUM SPEED
(> 50)
• 2002
MAXIMUM SPEED
(> 50)
• 2007
MINIMUM FREQ
(> 50)
• 2008
MAXIMUM FREQ
(> 50)
Parameter values are inconsistent. Check for the following:
PAR PFCREFNG
• 2007
MINIMUM FREQ
Parameter values are inconsistent. Check for any of the following:
PAR AI SCALE
• 1301
AI
• 1304
AI
Parameter values are inconsistent. Check for any of the following:
PAR AO SCALE
• 1504
AO
• 1510
2 Parameter values for power control are inconsistent: Improper motor
PAR PCU
nominal kVA or motor nominal power. Check for the following:
• 1.1 < (9906
• Where: P
or P
N
Parameter values are inconsistent. Check for the following:
PAR
EXTROMISSING
• Extension relay module not connected and
• 1410...1412
Parameter values are inconsistent. Check for and correct:
PAR
FBUSMISSING
• A parameter is set for fieldbus control (e.g. 1001
(
COMM
Parameter values are inconsistent – 9904
PAR
( :
PFCWOSCALAR SCALAR
1 Parameter values for power control are inconsistent: Improper motor
PAR PCU
nominal frequency or speed. Check for both of the following:
• 1 < (60 * 9907
• 0.8 < 9908
(120 * 9907
1
PAR PFC IO
IO configuration is not complete – not enough relays are parameterized to
PFC. Or, a conflict exists between Group 14, parameter 8117,
, and parameter 8118,
MOT
2
PAR PFC IO
IO configuration is not complete – the actual number of PFC motors
(parameter 8127,
and parameter 8118
3
PAR PFC IO
IO configuration is not complete – the drive is unable to allocate a digital
input (interlock) for each PFC motor (parameters 8120
8127
MOTORS
Description and Recommended Corrective Action
> 2002
MAXIMUM SPEED
> 2008
MAXIMUM FREQ
/ 9908
MOTOR NOM SPEED
/ 9908
MOTOR NOM SPEED
/ 9907
MOTOR NOM FREQ
/ 9907
MOTOR NOM FREQ
is negative, when 8123
1 > 1302 1 .
MIN AI MAX
2 > 1305 2 .
MIN AI MAX
1 > 1505 1 .
MIN AO MAX
2 > 1511 2 .
AO MIN AO MAX
* 9905
MOTOR NOM CURR
= 1000 * 9909
MOTOR NOM POWER
N
= 746 * 9909
MOTOR NOM POWER
4...6 have non-zero values.
RELAY OUTPUTS
)), but 9802
COMM PROT SEL
), when 8123
SPEED PFC ENABLE
MOTOR NOM FREQ
/
MOTOR NOM SPEED
/ Motor Poles) < 0.992
MOTOR NOM FREQ
AUTOCHNG INTERV
) does not match the PFC motors in Group 14
MOTORS
AUTOCHNG INTERV
).
.
.
is outside proper range
is outside proper range
is outside proper range
is outside proper range
is active.
PFC ENABLE
* 1.73 / P
MOTOR NOM VOLT
(if units are kW)
(if units are HP, e.g. in US)
1
EXT COMMANDS
= 0.
must be = 3
MOTOR CTRL MODE
is activated.
/ 9908 < 16
MOTOR NOM SPEED
.
.
INTERLOCKS
205
) < 3.0
N
= 10
NR OF AUX
and
Diagnostics