Mitsubishi Electric FR-A700 Technical Manual page 161

2.1.4 FR-D700
In the initial setting, only the simple mode parameters are
displayed. Set [Pr. 160 User group read selection] as required.
Initial Setting
[Pr. ] Name
Value Range
User group read 9999
160 9999
selection 0
[Pr.] Name
0 Torque boost 0 to 30%
1 Maximum frequency 0 to 120Hz
2 Minimum frequency 0 to 120Hz
3 Base frequency 0 to 400Hz
4 Multi-speed setting (high speed) 0 to 400Hz
5 Multi-speed setting (middle speed) 0 to 400Hz
6 Multi-speed setting (low speed) 0 to 400Hz
7 Acceleration time 0 to 3600s
8 Deceleration time 0 to 3600s
9 Electronic thermal O/L relay 0 to 500A
10 DC injection brake operation frequency 0 to 120Hz
11 DC injection brake operation time 0 to 10s
12 DC injection brake operation voltage 0 to 30%
- 13 Starting frequency 0 to 60Hz
- 14 Load pattern selection 0 to 3
15 Jog frequency 0 to 400Hz
16 Jog acceleration/deceleration time 0 to 3600s
- 17 MRS input selection 0, 2, 4
- 18 High speed maximum frequency 120 to 400Hz
- 19 Base frequency voltage 0 to 1000V, 8888, 9999
Acceleration/deceleration reference
20 1 to 400Hz
frequency
22 Stall prevention operation level 0 to 200%
Stall prevention operation level
23 0 to 200%, 9999
compensation factor at double speed
24 Multi-speed setting (speed 4) 0 to 400Hz, 9999
25 Multi-speed setting (speed 5) 0 to 400Hz, 9999
26 Multi-speed setting (speed 6) 0 to 400Hz, 9999
27 Multi-speed setting (speed 7) 0 to 400Hz, 9999
Acceleration/deceleration pattern
- 29 0, 1, 2
selection
- 30 Regenerative function selection 0, 1, 2
PARAMETER
• indicates simple mode parameters.
• The parameters marked with in the table allow
its setting to be changed during operation even if 0
(initial value) is set in [Pr. 77 Parameter write selection]
Remarks
Only the simple mode parameters can be displayed.
Simple mode+extended mode parameters can be displayed.
Minimum Setting Refer to
Setting Range Initial Value
Increments
0.1% 6/4/3%
*1
0.01Hz 120Hz
0.01Hz 0Hz
0.01Hz 60Hz
0.01Hz 60Hz
0.01Hz 30Hz
0.01Hz 10Hz
0.1s 5/10s
*2
0.1s 5/10s
*2
Rated inverter
0.01A
current
0.01Hz 3Hz
0.1s 0.5s
0.1% 4%
0.01Hz 0.5Hz
1 0
0.01Hz 5Hz
0.1s 0.5s 215, 234
1 0
0.01Hz 120Hz
0.1V 9999
0.01Hz 60Hz
0.1% 150%
0.1% 9999
0.01Hz 9999
0.01Hz 9999
0.01Hz 9999
0.01Hz 9999
1 0
1 0
188
• These instruction codes are used for parameter read
and write by using Mitsubishi inverter protocol with the
RS-485 communication.
[Pr.]
Page
244 0 00
232 1 01
232 2 02
244 3 03
216 4 04
216 5 05
216 6 06
234 7 07
234 8 08
379 9 09
325 10 0A
325 11 0B
328 12 0C
232 13 0D
244 14 0E
215 15 0F
16 10
56 17 11
232 18 12
244 19 13
234 20 14
283 22 16
335 23 17
216 24 18
216 25 19
216 26 1A
216 27 1B
238 29 1D
331 30 1E
• Symbols in the control mode-based correspondence table
indicate the following;
: Usable parameter
×: Unusable parameter
• Symbols in the parameter copy, parameter clear, and all
parameter clear columns indicate the following;
: Valid
×:
Invalid
Control Mode-based
Instruction Code
Correspondence Table
General-purpose
V/F control magnetic-flux
vector control
×
80 0
81 0
82 0
×
83 0
84 0
85 0
86 0
87 0
88 0
89 0
8A 0
8B 0
8C 0
8D 0
×
8E 0
8F 0
90 0
91 0
92 0
93 0
94 0
96 0
97 0
98 0
99 0
9A 0
9B 0
9D 0
9E 0
188
PARAMETER
2