7110030 HUAWEI 9000 HD Video Terminal V100R011 Administrator Guide Issue Date 2012-09-03 HUAWEI TECHNOLOGIES CO., LTD.
Page 2
Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
Page 3
VP9039A-TS), HUAWEI VP9036S, and HUAWEI VP9035A. T or TS indicates that the corresponding terminal is to be used in a Huawei telepresence system and M indicates that the corresponding terminal provides a built-in Multipoint Control Unit (MCU). You can check the bottom of a product to view its model.
Page 7
The quick start guide is provided along with the terminal in the product package. The administrator guide, user guide, and quick start guide are released on the Web site of Huawei (http://support.huawei.com).
The HUAWEI 9000 HD video terminal series (HUAWEI 9000 for short) is a series of new- generation HD video terminals provided by Huawei. The HUAWEI 9000 adopts advanced videoconferencing technologies to provide HD video and high-fidelity (hi-fi) audio.
Page 15
1080p (1920 × 1080 pixels and progressive scanning) 1080i (1920 × 1080 pixels and interlaced scanning) H.239 Dual-Stream The HUAWEI 9000 complies with the H.239 standard and supports concurrent video transmission using two channels. A presentation can either be a video or computer desktop content.
The user interface provides rich operation hints and statistics. Network The maximum call bandwidth is 8 Mbit/s. The HUAWEI 9000 supports Internet Protocol (IP), E1, 4E1, and public switched telephone network (PSTN) networks. The HUAWEI 9000 supports error concealment and lost packet recovery.
Page 21
The HD SDI OUT interface is an SMB interface that output supports HD-SDI signals and a 1.485 Gbit/s bandwidth. interface NOTE Only the ViewPoint 9039S and the HUAWEI VP9039A provide HD SDI OUT interfaces. HD OUT 3 HD video The HD OUT 3 interface is a DVI-I interface.
Page 22
SD OUT 1 interface so that CVBS and S-Video signals can be output. The SD OUT 1 interface of the HUAWEI VP9035A is an S-Video interface from which CVBS and S-Video signals are output.
SD IN 1 interface so that CVBS and S-Video signals can be input. The SD IN 1 interface of the HUAWEI VP9035A is an S-Video interface to which S-Video signals are input. A conversion cable can be connected to the SD IN 1 interface so that CVBS signals can be input.
Page 24
ViewPoint 9039 and the HUAWEI VP9039A as examples. Figure 1-15 shows the cable connection of the ViewPoint 9039 and the HUAWEI VP9039A in the simplest configuration. With the following cable connection, the terminal outputs HD video and uses the local area network (LAN) for communications. An HD camera is used for HD video input and a microphone array is used for audio input.
Page 26
9035, and ViewPoint 9033 are the same. The methods for powering on and powering off the ViewPoint 9030, ViewPoint 9039S, HUAWEI VP9035A, HUAWEI VP9036S, and HUAWEI VP9039A are the same. Therefore, the following sections take the ViewPoint 9039 and the ViewPoint 9030 as examples to describe the powering on and powering off process.
To use the terminal for video communications over a 3G network, a 3G data card must be inserted into a USB port of the terminal. Always use designated Huawei 3G data cards for the terminal. To enable the terminal to support 3G data cards, purchase a corresponding license that has the media access control (MAC) address and sequence number (SN) of the terminal.
If the data card is not a designated Huawei data card, the terminal fails to detect it, and a message appears on the screen indicating that no data card is available.
Page 42
During GK authentication, the password set on the terminal should be consistent with the password preset on the GK. Huawei GK Select this option when Huawei GK is used. If this option is not selected, some functions on the terminal are unavailable, such as Conference Control.
Borne by the standard IP protocol, the IMS uses voice over IP (VoIP) applications based on the standard SIP applications of the 3rd Generation Partnership Project (3GPP) to provide fixed and mobile multimedia services for operators. Integrating MCUs can enhance the functionality of the Huawei IMS HD videoconferencing solution. Proxy server...
When the HUAWEI 9000 communicates with the other vendors' devices, select Enable H.460. l When the HUAWEI 9000 communicates with Huawei devices, select Use NAT or Enable H.460.
HUAWEI VPC520 HD camera (VPC520 for short), HUAWEI VPC500S HD camera (VPC500S for short), and HUAWEI VPC500E HD camera (VPC500E for short). After a camera is connected to the terminal, it can be controlled using the COM interface of the terminal.
ViewPoint 9035: CVBS Camera PTZ l HUAWEI VP9035A: CVBS and S-Video On the HUAWEI VP9035A, only one of the HD IN 1 and SD IN 1 interfaces can be used at a time. Issue 09 (2012-09-03) Huawei Proprietary and Confidential...
Page 58
HUAWEI 9000 HD Video Terminal Administrator Guide 3 Camera and Display Table 3-3 Specifications of video input interfaces (ViewPoint 9039S and HUAWEI VP9039A) Video Input Type Receivable Input Format Control Interface HD IN 1 DVI-I DVI, SXGA, and YPrPb Camera PTZ...
Page 60
This specifies whether the terminal displays a reflection of an input video, wherein the right and left sides of the original are reversed. By default, Normal is selected. If the terminal is used in a Huawei telepresence system, select Horizontal mirroring.
This parameter is available on only the HUAWEI VP9035A. After this interface function is enabled, the SD IN 1 interface of the HUAWEI VP9035A is enabled and the HD IN 1 interface cannot be used. Signals of both the CVBS and S-Video types can be input to the SD IN 1 interface of the HUAWEI VP9035A.
Page 65
The SD OUT 1 interface of the HUAWEI VP9035A is an S-Video interface. l The SD OUT 1 interfaces of the ViewPoint 9039S, the HUAWEI VP9039A and the HUAWEI VP9036S are DVI interfaces. A DVI-(HDMI/VGA/S-Video/CVBS) conversion cable can be connected to the SD OUT 1 interface so that CVBS and S-Video signals can be output.
3 Camera and Display NOTE Please use the cables provided along with the HUAWEI 9000. Other cables may not be able to ensure the quality as desired. It is recommended that you contact the device supplier to purchase the relevant cables.
Page 69
③ SD OUT 1 Same as HD Same as HD OUT Same as HD OUT OUT 1 Table 3-15 Videos that can be output from each video output interface (on the HUAWEI VP9035A) Video Video Combined Default Video Default Video...
SDI OUT. For details about the combined picture, see "7.6 Adjusting the Screen Layout." NOTE Only the HUAWEI VP9039A and ViewPoint 9039S provide this parameter. Enable SD output By default, this option is deselected on HUAWEI VP9039A-T and interface selected on other terminals models.
The microphone array can work with the HUAWEI 9000 HD terminal series. Each terminal can support the cascading of up to three VPM210s. When two or three VPM210s are cascaded, one functions as the primary microphone array and the others as the secondary microphone arrays.
Page 77
R: The microphone is used to collect audio for the right audio channel. N: The microphone is not used. The Huawei logos of microphone arrays should point to the monitor.
Page 88
MCU of the ViewPoint 9039S is 6V + 3A, and the maximum number of sites supported by the built-in MCU of the HUAWEI VP9036S, ViewPoint 9030 and the HUAWEI VP9035A are 4V + 3A in which V stands for video sites and A stands for audio-only sites.
Page 89
NOTE The built-in MCUs of the ViewPoint 9039, ViewPoint 9036, HUAWEI VP9036S, ViewPoint 9039S, and HUAWEI VP9039A support the mixing of a maximum of three channels of audio streams, regardless of protocols. The numbers 12, 9, and 6 are the numbers of sites including the local site with the built-in MCU, that is, the built-in MCU site.
Page 93
The built-in MCUs of other terminal models do not support this function. If you use the built-in MCU of the HUAWEI VP9039A, the HUAWEI VP9036S, and the ViewPoint 9039S to hold a conference, a user at any participating site can set and view continuous presence after the conference starts.
5.1.8 Communicating with Microsoft Lync The terminal can call Microsoft Lync clients and view their online status. Huawei videoconferencing systems can be used in the Microsoft Unified Communications (MSUC) environment. Register the terminal (networked with MSUC) with a Lync server using SIP.
Page 99
Parameter Description Initial conference If you use the built-in MCU of the HUAWEI VP9039A to initiate a mode conference, you can set this parameter to either of the following: l Free view: All the sites participating in the conference can choose to view a specific site.
To enjoy HD effects, all the relevant devices, including the camera, video terminal, and display device, should support the HD capability. The HUAWEI 9000 supports the following HD resolutions: 1280 × 720 pixels (720p), 1280 × 1024 pixels, 1920 × 1080 pixels (1080p), and 1920 × 1080 pixels (1080i).
HUAWEI 9000 HD Video Terminal Administrator Guide 5 Initiating a Conference The HD capabilities of the HUAWEI 9000 are listed as follows: Sending HD video to remote sites Receiving HD video from remote sites Displaying HD video of the local site The terminal can send or receive the desktop contents of a computer while sending or receiving HD video.
5.5.1 Designing the Video and Presentation Capabilities The dual-stream mode can be used in point-to-point calls or in multipoint conferences. The dual-stream capabilities of the HUAWEI 9000 are listed as follows: One channel of HD video and one channel of SD video...
Borne by the standard IP protocol, IMS uses VoIP applications based on the standard SIP applications of the 3GPP to provide fixed and mobile multimedia services for operators. Integrating MCUs can enhance the functionality of the Huawei IMS HD videoconferencing solution.
If the site attends conferences hosted using traditional videoconferencing systems, select Ordinary site. l If the site attends conferences hosted using Huawei telepresence systems, select Telepresence site. l If the site is a Cisco TelePresence site and attends conferences held using Huawei videoconferencing systems, select CT site.
Page 116
MCU is being used. If the terminal whose built-in MCU is being used is the HUAWEI VP9039A, the ViewPoint 9039S or the HUAWEI VP9036S, the functions to view sites, disable chair control rights, end a conference, and set continuous presence are available.
7.1 Adjusting the Display Effects of the Video You can adjust the display effects of video by adjusting local video effects (such as the brightness and the saturation), the picture offset, the sampling phase, and by setting the HUAWEI VPC500/ VPC520 (VPC500/VPC520 for short) parameters.
7.1 Adjusting the Display Effects of the Video You can adjust the display effects of video by adjusting local video effects (such as the brightness and the saturation), the picture offset, the sampling phase, and by setting the HUAWEI VPC500/ VPC520 (VPC500/VPC520 for short) parameters.
----End 7.1.4 Adjusting Video Parameters After a Huawei HD camera is connected to the terminal, set the camera parameters, such as the exposure mode, white balance mode, aperture size, and noise reduction, to view quality video captured by the camera on monitors.
You can set video input interfaces for the local video, local presentation, and remote video. NOTE The ViewPoint 9039, ViewPoint 9036, ViewPoint 9035, ViewPoint 9033, ViewPoint 9030, and HUAWEI VP9035A support video input with a resolution of up to 1080p 30 Hz.
Page 166
Figure 11-1 Upgrading the software locally using a computer Step 4 Click Browser, and find the VCT.dat file. NOTE To independently upgrade the Huawei telepresence software running on the touch panel, select the HID.dat file. Step 5 Enter the IP address of the terminal, such as 10.10.10.10.
Page 178
The camera to be controlled is If a 3CCD camera is used along screen, the remote a 3CCD camera. with one of the HUAWEI 9000 at camera cannot be the remote site, reset the camera. controlled by The camera should then be...
Huawei products. To seek technical help over the Internet, please visit http://support.huawei.com. Please provide the following information that will help Huawei engineers to answer your questions effectively: – Serial number of the terminal (To view serial number, choose Diagnostics > System Information >...
Page 187
Warning: Changes or modifications made to this device not expressly approved by Huawei Technologies Co., Ltd. may void the FCC authorization to operate this device.
Page 191
ViewPoint 9033, and ViewPoint 9035: < 6.2 ViewPoint 9030, ViewPoint 9039S, HUAWEI VP9039A, HUAWEI VP9035A and HUAWEI VP9036S: < 5 kg NOTE l For details about the interfaces on the rear panel of each model, see section 1.3 Interfaces on the Rear Panel.