NEC Express5800/R120g Maintenance Manual page 199

Chapter 3 Appendix
Error Message
Cluster On Die was not ready. Cluster On Die feature is
A428
DIMM population is
A429 insufficient for Cluster On
Die.
Memory not detected
A800
PEI_MEMORY_NONE_USEFUL
A801
Latest memory module is
A804
corrupted.
AE01 CPU1_DIMM1 has been
disabled.
AE02 CPU1_DIMM2 has been
disabled.
AE03 CPU1_DIMM3 has been
disabled.
AE04 CPU1_DIMM4 has been
disabled.
AE05 CPU1_DIMM5 has been
disabled.
AE06 CPU1_DIMM6 has been
disabled.
AE07 CPU1_DIMM7 has been
disabled.
AE08 CPU1_DIMM8 has been
disabled.
AE0D CPU2_DIMM1 has been
disabled.
AE0E CPU2_DIMM2 has been
disabled.
AE0F CPU2_DIMM3 has been
disabled.
AE10 CPU2_DIMM4 has been
disabled.
AE11 CPU2_DIMM5 has been
disabled.
AE12 CPU2_DIMM6 has been
disabled.
AE13 CPU2_DIMM7 has been
disabled.
AE14 CPU2_DIMM8 has been
disabled.
AE81 CPU1_DIMM1 with error is
enabled.
AE82 CPU1_DIMM2 with error is
enabled.
Cause
disabled in this hardware
configuration.
Cluster On Die feature is
disabled in this memory
configuration.
No valid memory is installed.
No available memory is
installed.
Failure on BIOS Flash ROM
was detected.
A memory error was detected.
CPU1_DIMM1 has been
disabled.
A memory error was detected.
CPU1_DIMM2 has been
disabled.
A memory error was detected.
CPU1_DIMM3 has been
disabled.
A memory error was detected.
CPU1_DIMM4 has been
disabled.
A memory error was detected.
CPU1_DIMM5 has been
disabled.
A memory error was detected.
CPU1_DIMM6 has been
disabled.
A memory error was detected.
CPU1_DIMM7 has been
disabled.
A memory error was detected.
CPU1_DIMM8 has been
disabled.
A memory error was detected.
CPU2_DIMM1 has been
disabled.
A memory error was detected.
CPU2_DIMM2 has been
disabled.
A memory error was detected.
CPU2_DIMM3 has been
disabled.
A memory error was detected.
CPU2_DIMM4 has been
disabled.
A memory error was detected.
CPU2_DIMM5 has been
disabled.
A memory error was detected.
CPU2_DIMM6 has been
disabled.
A memory error was detected.
CPU2_DIMM7 has been
disabled.
A memory error was detected.
CPU2_DIMM8 has been
disabled.
An error in CPU1_DIMM1 was
detected, but because all
memory is currently disabled,
this DIMM was forcibly enabled.
An error in CPU1_DIMM2 was
detected, but because all
memory is currently disabled,
this DIMM was forcibly enabled.
Express5800/R120g-2E, T120g Maintenance Guide
Solution
Replace the processor with the one that supports
this feature. Or, run SETUP and select Disabled
for the Cluster On Die. If the same error persists,
contact your sales representative.
Check if memory configuration is correct. If the
same error persists, contact your sales
representative.
Check if DIMMs are properly installed. If the same
message appears repeatedly, contact your sales
representative.
Check if the memory configuration is correct. If
the same message appears repeatedly, contact
your sales representative.
Contact your sales representative.
1. POST Error Message
199