Mitsubishi Electric melsec q00ujcpu User Manual page 485

ACPU Special Special
Special Relay after Relay for
Relay Conversion Modification
M9103 SM1103 SM323
M9104 SM1104 SM324
M9108 SM1108 SM90
M9109 SM1109 SM91
M9110 SM1110 SM92
M9111 SM1111 SM93
M9112 SM1112 SM94
M9113 SM1113 SM95
M9114 SM1114 SM96
M9196 SM1196 SM325
M9197 SM1197
M9198 SM1198
M9199 SM1199
(10) QCPU with built-in Ethernet port
Number Name
Time setting function
SM1270 (SNTP client)
execution
Remote password
SM1273
mismatch count clear
* 1: This applies to the Built-in Ethernet port QCPU.
12 - 19
Table12.11 Special relay
Name
OFF : Continuous transition
Presence/absence
of continuous
ON : Continuous transition
transition
Continuous OFF : When transition is
transition
suspension flag ON : When no transition
Step transition
monitoring timer
start (equivalent of
SD90)
Step transition
monitoring timer
start (equivalent of
SD91)
Step transition
monitoring timer
start (equivalent of
SD92)
Step transition
OFF : Monitoring timer reset
monitoring timer
ON : Monitoring timer reset
start (equivalent of
SD93)
Step transition
monitoring timer
start (equivalent of
SD94)
Step transition
monitoring timer
start (equivalent of
SD95)
Step transition
monitoring timer
start (equivalent of
SD96)
Operation output OFF : Coil output OFF
at block stop ON : Coil output ON
SM
1197
OFF
Switch between
blown fuse and I/O ON
verify error display
OFF
ON
Data recovery of
OFF : Data recovery disabled
online sampling
ON : Data recovery enabled
trace/status latch
Table12.12 Special relay
Meaning
OFF : No time setting function Set this to ON when executing the time setting function
(SNTP client) execution (SNTP client).
ON : Time setting function (Only when the time setting function is in "Use" with the
(SNTP client) execution time setting parameter.)
To clear the acumulated numeber (SD979 to 999) of
OFF : Normal
mismatched remote passwords, the setting SM1273 is
ON : Clear
executed.
Meaning
• Set whether continuous transition will be performed for the
not effective
block where the "continuous transition bit" of the SFC
information device is not set.
effective
• OFF during operation in the continuous transition mode or
during continuous transition, and ON when continuous
completed transition is not executed.
• Always ON during operation in the no continuous
transition mode.
• Turns ON when the measurement of the step transition
monitoring timer is started.
Turning this relay OFF resets the step transition
start
monitoring timer.
• Selects the operation output when block stop is executed.
ON : Retains the ON/OFF status of the coil being used
by using operation output of the step being
executed at block stop.
OFF : All coil outputs are turned off. (Operation output
by the SET instruction is retained regardless of
the ON/OFF status of SM1196.)
I/O numbers
SM
to be
1198
displayed
OFF X/Y0 to 7F0
Switches I/O numbers in the fuse blow module storage
X/Y800 to registers (SD1100 to SD1107) and I/O module verify error
OFF
FF0 storage registers (SD1116 to SD1123) according to the
combination of ON/OFF of the SM1197 and SM1198.
X/Y1000 to
ON
17F0
X/Y1800 to
ON
1FF0
• Recovers the setting data stored in the CPU module at
restart when sampling trace/status latch is executed.
• SM1199 should be ON to execute again. (Unnecessary
when writing the data again from peripheral devices.)
Explanation
Corresponding
Details
Corres-
ponding
Set by Corresponding
ACPU
(When Set)
M9
U New
U New
CPU
Qn(H)
QnPH
CPU
*1
QnU