Notes For Frame R8; Input Power Cable - ABB ACS560 Hardware Manual

Motor cable
6. Cut an adequate hole into the rubber grommet. Slide the grommet onto the cable.
figure. If you use aluminum cables, put grease to the peeled aluminum cable
7. Prepare the ends of the input power cable and motor cable as illustrated in the
6. Cut an adequate hole into the rubber grommet. Slide the grommet onto the cable.
before connecting it to the drive. Two different motor cable types are shown in the
figure. If you use aluminum cables, put grease to the peeled aluminum cable
figures (7a, 7b).
7. Prepare the ends of the input power cable and motor cable as illustrated in the
before connecting it to the drive. Two different motor cable types are shown in the
figure. If you use aluminum cables, put grease to the peeled aluminum cable
figures (7a, 7b).
Note: The bare shield will be grounded 360 degrees. Mark the pigtail made from
before connecting it to the drive. Two different motor cable types are shown in the
Note: The bare shield will be grounded 360 degrees. Mark the pigtail made from
the shield as a PE conductor with yellow-and-green color.
figures (7a, 7b).
the shield as a PE conductor with yellow-and-green color.
Note: The bare shield will be grounded 360 degrees. Mark the pigtail made from
6
6
the shield as a PE conductor with yellow-and-green color.
6
7b
7b
7b
PE
PE
8. Slide the cables through the holes of the lead-through plate and attach the
grommets to the holes (the motor cable to the right and the input power cable to
the left).
9. Connect the motor cable as follows:
8. Slide the cables through the holes of the lead-through plate and attach the
• Ground the shield 360 degrees under the grounding clamps.
8. Slide the cables through the holes of the lead-through plate and attach the
grommets to the holes (the motor cable to the right and the input power cable to
• Connect the twisted shield of the cable to the grounding terminal (9a).
grommets to the holes (the motor cable to the right and the input power cable to
8. Slide the cables through the holes of the lead-through plate and attach the grommets to
the left).
the left).
• Connect the phase conductors of the cable to terminals T1/U, T2/V and T3/W.
the holes (the motor cable to the right and the input power cable to the left).
Tighten the screws to the torque given in the figure (9b).
9. Connect the motor cable as follows:
9. Connect the motor cable as follows:
9. Connect the motor cable as follows:
• • Ground the shield 360 degrees under the grounding clamps. Ground the shield 360 degrees under the grounding clamps.
• Ground the shield 360 degrees under the grounding clamps.
• Connect the twisted shield of the cable to the grounding terminal (9a).
• Connect the twisted shield of the cable to the grounding terminal (9a).
• Connect the twisted shield of the cable to the grounding terminal (9a).
• Connect the phase conductors of the cable to terminals T1/U, T2/V and T3/W. Tighten • Connect the phase conductors of the cable to terminals T1/U, T2/V and T3/W.
• Connect the phase conductors of the cable to terminals T1/U, T2/V and T3/W.
the screws to the torque given in the figure (9b).
Tighten the screws to the torque given in the figure (9b).
Tighten the screws to the torque given in the figure (9b).

Notes for frame R8

• If you connect only one conductor to the connector, we recommend that you put it under
the upper pressure plate.
• The connectors are detachable but we do not recommend that you detach them. If you
do, detach and reinstall the connectors as follows.

Input power cable

10. Connect the input power cable as in step 9.
7a
7a 7b 7a
7a 7b
7a
7a 7b
PE
Electrical installation 77
PE
PE
PE