ABB ACS560 Hardware Manual page 78

under the upper pressure plate.
under the upper pressure plate.
• The connectors are detachable but we do not recommend that you detach them.
• The connectors are detachable but we do not recommend that you detach them.
If you do, detach and reinstall the connectors as follows.
If you do, detach and reinstall the connectors as follows.
78 Electrical installation
Input power cable Input power cable
10. Connect the input power cable as in step 9. Use terminals L1, L2 and L3. 10. Connect the input power cable as in step 9. Use terminals L1, L2 and L3.
M5×25/35
M5×25/35
Frame size
Frame size
R6
Frame size
R6
R7
R7
R8
R8
R5
Terminals T1/U, T2/V and T3/W
R6
Terminals T1/U, T2/V and T3/W
• Remove the nut that attaches the connector to its busbar. R7
• Remove the nut that attaches the connector to its busbar.
• Put the conductor under the connector pressure plate and pre-tighten the
R8
• Put the conductor under the connector pressure plate and pre-tighten the
conductor.
conductor.
Terminals T1/U, T2/V and T3/W
• Put the connector back to its busbar. Start the nut, and turn it at least two
• Put the connector back to its busbar. Start the nut, and turn it at least two
• Remove the nut that attaches the connector to its busbar.
rotations by hand.
rotations by hand.
• Put the conductor under the connector pressure plate and pre-tighten the conductor.
• Put the connector back to its busbar. Start the nut, and turn it at least two rotations by
WARNING! Before using tools, make sure that the nut/screw is not cross-
WARNING! Before using tools, make sure that the nut/screw is not cross-
hand.
threading. Cross-threading will damage the drive and cause danger.
threading. Cross-threading will damage the drive and cause danger.
WARNING!
• Tighten the nut to a torque of 30 N·m (22 lbf·ft).
Before using tools, make sure that the nut/screw is not cross-threading.
• Tighten the nut to a torque of 30 N·m (22 lbf·ft).
• Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m
Cross-threading will damage the drive and cause danger.
• Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m
(52 lbf·ft) for frame R8.
(52 lbf·ft) for frame R8.
• Tighten the nut to a torque of 30 N·m (22 lbf·ft).
• Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m (52 lbf·ft) for
frame R8.
Terminals L1, L2 and L3
• Remove the combi screw that attaches the connector to its terminal post, and pull the
connector off.
• Put the conductor under the connector pressure plate and pre-tighten the conductor.
• Put the connector back onto the terminal post. Start the combi screw, and turn it at least
two rotations by hand.
9b
9b 10b
9a
9a
8
8
L1, L2, L3, T1/U, T2/V, T3/W
L1, L2, L3, T1/U, T2/V, T3/W
N·m lbf·ft
N·m lbf·ft
30 22.1
L1, L2, L3, T1/U, T2/V, T3/W
30 22.1
40 29.5
40 29.5
40 29.5
N·m lbf·ft
40 29.5
5.6 4.1
30 22.1
40 29.5
40 29.5
10b
10a
10a
8
8
PE,
PE,
N·m N·m
N·m N·m
9.8 7.2
9.8 7.2
PE
9.8 7.2
9.8 7.2
9.8 7.2
N·m lbf·ft
9.8 7.2
2.2 1.6
9.8 7.2
9.8 7.2
9.8 7.2
N·m lbf·ft
N·m lbf·ft
N·m lbf·ft
1.2 0.9
1.2 0.9
1.2 0.9
1.2 0.9