ABB i-bus KNX Product Manual page 5

11.5.43
11.5.44
11.5.45
11.5.46
11.5.47
11.5.48
11.5.49
11.5.50
11.5.51
11.5.52
11.5.53
11.5.54
11.5.55
11.5.56
11.5.57
11.5.58
11.5.59
11.5.60
11.5.61
11.5.62
11.5.63
11.5.64
11.5.65
11.5.66
11.5.67
11.5.68
11.5.69
11.5.70
11.5.71
11.5.72
11.5.73
11.5.74
11.5.75
11.5.76
11.5.77
11.5.78
11.5.79
11.5.80
11.5.81
11.5.82
11.5.83
11.5.84
11.5.85
11.5.86
11.5.87
11.5.88
11.5.89
11.5.90
11.5.91
11.5.92
11.5.93
Product manual 2CKA001473B9482
Cooling control - Control value type ............................................................................................... 92
Cooling control - Cooling type ........................................................................................................ 93
Cooling control - P-component (x 0.1°C) ....................................................................................... 93
Cooling control - I-component (min.).............................................................................................. 94
Cooling control - Extended settings ............................................................................................... 94
Basic stage cooling............................................................................................................................ 95
Basic stage cooling - Status object cooling ................................................................................... 95
Basic stage cooling - Mode of the control value ............................................................................ 95
Basic stage heating - Control value difference for sending of heating control value ..................... 95
Basic stage cooling - Hysteresis (x 0.1°C) .................................................................................... 96
Basic stage cooling - Cyclic sending of the control value (min) ................................................... 96
Basic stage cooling - PWM cycle cooling (min) ............................................................................... 97
Basic stage cooling - Maximum control value (0 - 255) ................................................................ 97
Basic stage cooling - Minimum control value for basic load (0 to 255) ........................................ 97
Control of additional cooling stage ................................................................................................... 98
Control of additional cooling stage - Cooling type ......................................................................... 99
Control of additional cooling stage - P-component (x 0.1°C) ....................................................... 99
Control of additional cooling stage - P-component (min) ............................................................ 100
Control of additional cooling stage - Temperature difference to basic stage (x 0.1°C) ............... 100
Control of additional cooling stage - Extended settings .............................................................. 100
Additional cooling stage .................................................................................................................. 101
Additional cooling stage - Mode of the control value .................................................................. 101
Additional cooling stage - Hysteresis (x 0.1°C) ........................................................................... 101
Additional cooling stage - Control value difference for sending of cooling control value .......... 101
Additional cooling stage - Cyclic sending of the control value (min) .......................................... 102
Additional cooling stage - Maximum control value (0 - 255) ....................................................... 102
Additional cooling stage - Minimum control value for basic load (0 - 255) ................................ 102
Settings of basic load ...................................................................................................................... 103
Settings of basic load - Minimum control value for basic load > 0 ............................................. 103
Basic load settings - Basic load active when controller is off ..................................................... 103
Combined heating and cooling modes ........................................................................................... 104
Combined heating and cooling modes - Switchover of heating/cooling .................................... 104
Combined heating and cooling modes - Operating mode after reset ........................................ 104
Combined heating and cooling modes - Heating/cooling control value output ......................... 105
Combined heating and cooling modes - Additional heating/cooling stage control value
output ............................................................................................................................................... 105
Setpoint settings .............................................................................................................................. 106
Setpoint settings - Setpoint for heating comfort = setpoint for cooling comfort ......................... 106
Setpoint settings - Hysteresis for switchover heating/cooling (x 0.1°C)..................................... 106
Setpoint settings - Setpoint temperature for heating and cooling comfort (°C) ......................... 107
Setpoint settings - Setpoint temperature for heating comfort (°C) ............................................. 107
Setpoint settings - Reduction for standby heating (°C) ............................................................... 107
Setpoint settings - Reduction for ECO heating (°C) .................................................................... 107
Setpoint settings - Set-point temperature for frost protection (°C) ............................................. 108
Setpoint settings - Setpoint temperature for cooling comfort (°C) .............................................. 108
Setpoint settings - Increase for standby cooling (°C) .................................................................. 108
Setpoint settings - Increase for ECO cooling (°C) ....................................................................... 108
Setpoint settings - Set-point temperature for heat protection (°C) ............................................. 109
Setpoint settings - Display indicates ............................................................................................ 109
Setpoint settings - Send current setpoint ..................................................................................... 109
Setpoint settings - Cyclic sending of the current set-point temperature (min) ........................... 109
Setpoint settings - Basic set value is .............................................................................................. 110
Table of contents
│5