Upgrading System Software In Hot Standby Scenarios (Applicable To Versions Earlier Than V500R001C30Spc300) - Huawei USG6000 Upgrade Manual

HUAWEI USG6000&USG9500
Upgrade Guide
HRP_M<FW_A> system-view
HRP_M[FW_A] interface GigabitEthernet 1/0/7
HRP_M[FW_A-GigabitEthernet1/0/7] undo shutdown
HRP_M[FW_A-GigabitEthernet1/0/7] quit
Step 12 Wait for the session entries to be synchronized between the active and standby FWs. It takes
around two minutes to synchronize the entries. You can run the display firewall session table
command to check whether the numbers of sessions on the two FWs are consistent. If yes,
continue the following operations.
Step 13 Run the undo shutdown command to enable the service interface of FW_A.
HRP_S[FW_A] interface GigabitEthernet 1/0/3
HRP_S[FW_A-GigabitEthernet1/0/3] undo shutdown
HRP_S[FW_A-GigabitEthernet1/0/3] quit
HRP_S[FW_A] interface GigabitEthernet 1/0/1
HRP_S[FW_A-GigabitEthernet1/0/1] undo shutdown
HRP_S[FW_A-GigabitEthernet1/0/1] quit
HRP_S[FW_A] quit
HRP_S<FW_A> save
Info: The system is now comparing the configuration, please wait.
Warning: The configuration has been modified, and it will be saved to the next s
tartup saved-configuration file hda1:/vrpcfg.zip. Continue? [Y/N]:y
Now saving the current configuration to the slot 0....
Save the configuration successfully.
----End
Verification
1.
2.
1.4.3 Upgrading System Software in Hot Standby Scenarios
(Applicable to Versions Earlier Than V500R001C30SPC300)
This section describes how to upgrade system software in hot standby scenarios.
Networking Requirements
As shown in
interface, GE1/0/1 the upstream service interface, and GE1/0/3 the downstream service
interface. You need to upgrade system software versions of the two FWs to a specified
version.
Issue 01 (2018-01-16)
Test whether services are normal.
Test the active/standby switchover.
Configure a PC in the intranet to constantly the internet host and run the shutdown
command on GE1/0/1 of FW_A. Then check the status switchover of the FW and
discarded ping packets. If the status switchover is normal, FW_B switches to the active
device and carries services. The command prompt of FW_B is changed from HRP_S to
HRP_M, and the command prompt of FW_A is changed from HRP_M to HRP_S. No or
several ping packets (1 to 3 packets, depending on actual network environments) are
discarded.
Run the undo shutdown command on GE1/0/1 of FW_A and check the status
switchover of the FW and discarded ping packets. If the status switchover is normal,
FW_A switches to the active device and starts to carry service after the preemption delay
(60s by default) expires. The command prompt of FW_A is changed from HRP_S to
HRP_M, and the command prompt of FW_B is changed from HRP_M to HRP_S. No or
several ping packets (1 to 3 packets, depending on actual network environments) are
discarded.
Figure 1-44, two FWs work in active/standby mode. GE1/0/7 is the heartbeat
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1 USG6000
78