Toro GreensPro 1200 Service Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. GreensPro 1200
  6. Service manual
Toro GreensPro 1200 Service Manual

Toro GreensPro 1200 Service Manual

Hide thumbs Also See for GreensPro 1200:
Table of Contents

Advertisement

Quick Links

Preface
The purpose of this publication is to provide the service
technician with information for troubleshooting, testing,
and repairing assemblies and components on the
GreensPro 1200.
REFER TO THE OPERATOR'S MANUAL FOR
OPERATING, MAINTENANCE, AND ADJUSTMENT
INSTRUCTIONS. Space is provided in Chapter 2 of
this book to insert the Operator's Manual and Parts
Catalog for your machine. Replacement catalogs are
available on the Internet at www.toro.com.
The Toro Company reserves the right to change
product specifications or this publication without notice.
This
WARNING, or CAUTION, PERSONAL SAFETY
INSTRUCTION. When you see this symbol,
carefully read the instructions that follow.
Failure to obey the instructions may result in
personal injury.
NOTE: A NOTE will give general information about the
correct operation, maintenance, service, testing, or
repair of the machine.
IMPORTANT: The IMPORTANT notice will give
important instructions which must be followed to
prevent damage to systems or components on the
machine.
© The Toro Company - 2013

Service Manual

GreensPro™ 1200
safety
symbol
means
PART NO. 12193SL
DANGER,

Advertisement

Table of Contents
loading

Related Manuals for Toro GreensPro 1200

Summary of Contents for Toro GreensPro 1200

  • Page 1: Service Manual

    Internet at www.toro.com. NOTE: A NOTE will give general information about the correct operation, maintenance, service, testing, or The Toro Company reserves the right to change repair of the machine. product specifications or this publication without notice.
  • Page 2 This page is intentionally blank. Greens Pro 1200...
  • Page 3 Table Of Contents Chapter 1 - Safety Safety Instructions ........... 1-2 Safety and Instruction Decals ........1-4 Chapter 2 - Product Records and Maintenance Product Records ............2-2 Maintenance ............2-2 Equivalents and Conversions ........2-3 Torque Specifications ..........2-4 Chapter 3 - Gasoline Engine Introduction ..............
  • Page 4 This page is intentionally blank. Greens Pro 1200...

  • Page 5: Table Of Contents

    Chapter 1 Safety Safety Table of Contents Safety Instructions ........1-2 Before Operating ..........1-2 While Operating..........1-2 Maintenance and Service ........1-3 Safety and Instruction Decals ...... 1-4 GreensPro 1200 Page 1 - 1 Safety...

  • Page 6: Safety Instructions

    To reduce the potential for injury or death, comply with the following safety instructions. GreensPro 1200 machines have been tested and certified by Toro for compliance with existing safety standards and specifications. Although hazard control...

  • Page 7: Maintenance And Service

    GreensPro machine. Refer to these publications for machine, use genuine TORO replacement parts and additional information when servicing the machine. accessories. Replacement parts and accessories made by other manufacturers may result in non- 2.

  • Page 8: Safety And Instruction Decals

    Replace any decal that is damaged or lost. Decal part numbers are listed in your Parts Catalog. Order replacement decals from your Authorized TORO Distributor. Safety Page 1 - 4...

  • Page 9: Product Records

    Standard Torque for Dry, Zinc Plated, and Steel Fasteners (Inch Series Fasteners) .... 2-5 Standard Torque for Dry, Zinc Plated, and Steel Fasteners (Metric Fasteners) ....2-6 Other Torque Specifications ....... 2-7 Conversion Factors ..........2-7 GreensPro 1200 Page 2 - 1 Product Records and Maintenance...
  • Page 10 Product Records Insert Operator’s Manual and Parts Catalog for your GreensPro 1200 at the end of this section. In addition, if any optional equipment or accessories have been installed to your machine, insert the Installation Instructions, Operator’s Manuals, and Parts Catalogs for those options at the end of this chapter.

  • Page 11: U.s. To Metric Conversions

    Foot-pounds Kilogram-Meters 0.1383 Kilograms-Centimeter 1.152144 Inch-pounds Liquid Volume Quarts Liters 0.9463 Gallons Liters 3.785 Liquid Flow 3.785 Gallon/Minutes Liters/Minute Temperature Fahrenheit Celsius 1. Subtract 32 ˚ 2. Multiply by 5/9 GreensPro 1200 Page 2 - 3 Product Records and Maintenance...

  • Page 12: Torque Specifications

    For critical applications, as determined be reduced by 25% for lubricated fasteners to achieve by Toro, either the recommended torque or a torque the similar stress as a dry fastener. Torque values may that is unique to the application is clearly identified and also have to be reduced when the fastener is threaded specified in this Service Manual.

  • Page 13: Standard Torque For Dry, Zinc Plated, And Steel Fasteners (Inch Series Fasteners)

    NOTE: Reduce torque values listed in the table above by 25% for lubricated fasteners. Lubricated fasteners are defined as threads coated with a lubricant such as ® engine oil or thread sealant such as Loctite GreensPro 1200 Page 2 - 5 Product Records and Maintenance...

  • Page 14: Standard Torque For Dry, Zinc Plated, And Steel Fasteners (Metric Fasteners)

    NOTE: Reduce torque values listed in the table above by 25% for lubricated fasteners. Lubricated fasteners are defined as threads coated with a lubricant such as ® engine oil or thread sealant such as Loctite Product Records and Maintenance Page 2 - 6 GreensPro 1200...

  • Page 15: Other Torque Specifications

    11.298 = N·cm N·cm x 0.08851 = in-lb in-lb x 0.1130 = N·m N·m x 8.851 = in-lb ft-lb x 1.3558 = N·m N·m x 0.7376 = ft-lb GreensPro 1200 Page 2 - 7 Product Records and Maintenance...
  • Page 16 This page is intentionally blank. Product Records and Maintenance Page 2 - 8 GreensPro 1200...
  • Page 17 Table of Contents Introduction ............ 3-2 Operator’s Manual ..........3-2 Engine Identification ........... 3-2 Specifications ..........3-3 General Information........3-4 Fuel Evaporative Control System ....... 3-4 Service and Repairs ........3-5 Engine ..............3-5 GreensPro 1200 Page 3 - 1 Gasoline Engine...

  • Page 18: Introduction

    Authorized TORO Distributor. Be prepared to provide When disposing of hazardous waste products, take your distributor with the TORO model and serial them to an authorized disposal site. Waste products number of your machine to obtain parts. must not be allowed to contaminate surface water, drains, or sewer systems.

  • Page 19: Specifications

    0.63 U.S. Quarts (0.6 Liters) Air Cleaner Dual Element Ignition System Transistorized Flywheel Magneto Spark Plug NGK BPR6ES Spark Plug Gap 0.028 to 0.031 in. (0.7 to 0.8 mm) Dry Weight 35.5 lb (16.1 kg) GreensPro 1200 Page 3 - 3 Gasoline Engine...

  • Page 20: General Information

    (1). The insert also prevents the fuel from saturating the fuel cap during machine movement. Do not overfill the tank when refueling. Refer to the Honda GX200 Owner’s Manual for additional information. Gasoline Engine Page 3 - 4 GreensPro 1200...

  • Page 21: Service And Repairs

    7. Remove lock nuts (9), cap screws (10), and flat washers (11). 8. Remove the engine. Figure 3 5. Remove three lock nuts (6), three cap screws (7), and six flat washers (8). GreensPro 1200 Page 3 - 5 Gasoline Engine...
  • Page 22 313000000, measure and record the distance from the end of the engine collar (17) to the engine cover before removing the collar to ensure correct installation. Loosen set screw (18) and remove engine collar (17) and square key (16). Gasoline Engine Page 3 - 6 GreensPro 1200...
  • Page 23 Secure the engine collar by tightening set screw (4). Figure 11 3. Install drive coupling (12) using two lock nuts (13), flat washers (14), and cap screws (15). GreensPro 1200 Page 3 - 7 Gasoline Engine...
  • Page 24 (16), cap screws (17), and flat washers (18). 20 21 22 Figure 14 5. Install rear support frame (19) using three lock nuts (20), three cap screws (21), and six flat washers (22). Gasoline Engine Page 3 - 8 GreensPro 1200...
  • Page 25 Service and Repairs ........4-8 Transmission ............4-8 Transmission Service ........4-13 Drive Chain Tension Assembly ......4-15 Oil Tank ............4-16 Oil Filter Assembly..........4-19 HYDRO-GEAR BDR SERVICE AND REPAIR MANUAL GreensPro 1200 Page 4 - 1 Hydraulic System...

  • Page 26: Introduction

    Some service and repair parts for the transmission in your GreensPro machine are supplied through your Authorized TORO Distributor. Be prepared to provide your distributor with the TORO model and serial number of your machine to obtain parts. When disposing of hazardous waste products, take them to an authorized disposal site.

  • Page 27: Specifications

    Pump Displacement (per revolution) 0.62 in (10.2 cc) Motor Displacement (per revolution) 1.33 in (21.8 cc) Hydraulic Tank Capacity 5.3 U.S. Quarts (5.0 Liters) Hydraulic Oil See Operator’s Manual Hydraulic Filter Spin-on Cartridge Type GreensPro 1200 Page 4 - 3 Hydraulic System...
  • Page 28 This page is intentionally blank. Hydraulic System Page 4 - 4 GreensPro 1200...

  • Page 29: General Information

    IMPORTANT: The hydraulic fittings and hoses used 5. Thread the hydraulic hose swivel nut onto the fitting on the GreensPro 1200 have both SAE and BSP by hand. While holding the hose with a wrench to threads. If fittings or hoses are replaced, make sure...

  • Page 30: Using A Torque Wrench With An Offset Wrench

    If the listed torque recommendation for a fastener is from 76 to 94 lb-ft, the proper torque when using this torque wrench with an offset wrench would be from 72 to 98 lb-ft. Figure 1 Hydraulic System Page 4 - 6 GreensPro 1200...

  • Page 31: Relieving Hydraulic System Pressure

    Before disconnecting or performing any work on the To relieve hydraulic pressure in the traction circuit, GreensPro 1200 hydraulic system, all pressure in the depress each of the motion pedals fully. hydraulic system must be relieved. Park machine on a level surface.

  • Page 32: Service And Repairs

    7. Put clean plugs in disconnected hoses and fittings to prevent system contamination. 10 11 12 13 Figure 4 10. Remove two lock nuts (10), two washers (11), two cap screws (12), and four bushings (13). Hydraulic System Page 4 - 8 GreensPro 1200...
  • Page 33 13. Remove nut (20) and flat washer (21). 14. Remove lock nut (18), flat washer (17), cap screw ® (24), flat washer (22), pivot bushing (25), two Oilite bushings (26), and spacer (19), and remove idler arm assembly (23). GreensPro 1200 Page 4 - 9 Hydraulic System...
  • Page 34 5. Remove lock nut (12), cap screw (10), two flat cap screws (1), three lock nuts (2), and six flat washers washers (9), and spacer (8), and remove damper plate (3). (11). Hydraulic System Page 4 - 10 GreensPro 1200...
  • Page 35 (26), lock nut (24), and two flat washers (25). 8. Install cap screw (15), lock nut (16), and two flat 11. Connect damper (22) using nut (23). washers (17) at the bottom of the transmission. GreensPro 1200 Page 4 - 11 Hydraulic System...
  • Page 36 18. Operate machine. Check oil level and adjust if necessary. Check components for leaks. Tighten any loose connections. 19.Raise machine onto transport wheels, check transmission return to neutral setting and adjust as necessary. (See HYDRO-GEAR BDR SERVICE AND REPAIR MANUAL.) Hydraulic System Page 4 - 12 GreensPro 1200...

  • Page 37: Transmission Service

    15. Pump block assembly 24. Motor shaft 7. Retaining ring 16. Hollow pin (2 used) 25. Thrust bearing 8. Ball bearing 17. Charge relief spring 26. Ball bearing 9. Plug 18. Ball 27. Retaining ring GreensPro 1200 Page 4 - 13 Hydraulic System...
  • Page 38 35. Lock nut 44. O-ring 53. Extension spring 36. Bypass arm 45. Charge pump NOTE: The Hydro-Gear BDR transmission used in your GreensPro 1200 is illustrated in Figure 16. If transmission part numbers are not identified in your Parts Catalog, contact your...

  • Page 39: Drive Chain Tension Assembly

    (8), idler sprocket assembly (3), and bolt (4) from idler arm (18). NOTE: Perform step 5 only if it is necessary to replace bearings (5). 5. Remove two bearings (5) and spacer (7) from idler sprocket (6). GreensPro 1200 Page 4 - 15 Hydraulic System...

  • Page 40: Oil Tank

    6. Label all hoses and fittings for assembly purposes. Remove hoses (1 and 2) from fittings on oil tank. Drain hoses into a suitable container. 7. Put clean plugs in disconnected hoses and fittings to prevent system contamination. Hydraulic System Page 4 - 16 GreensPro 1200...
  • Page 41 8. Oil tank 12. Drain plug 9. Seal (2 used) 13. Decal 10. Adapter fitting (2 used) 10. Remove two adapter fittings (10) and seals (9). 11. Remove drain plug (12) and seal (11). GreensPro 1200 Page 4 - 17 Hydraulic System...
  • Page 42 Transmission Cover in the Service and Repairs section of Chapter 5 - Chassis). 8. Lower and secure seat platform. 9. Operate machine. Check oil level and adjust if necessary. Check components for leaks. Tighten any loose connections. Hydraulic System Page 4 - 18 GreensPro 1200...

  • Page 43: Oil Filter Assembly

    7. Put clean plugs in disconnected hoses and fittings to prevent system contamination. 8. Remove two cap screws (2), lock washers (3), and flat washers (4), and remove oil filter assembly (6). GreensPro 1200 Page 4 - 19 Hydraulic System...
  • Page 44 Transmission Cover in the Service and Repairs section of Chapter 5 - Chassis). 7. Lower and secure seat platform. 8. Operate machine. Check oil level and adjust if necessary. Check components for leaks. Tighten any Hydraulic System Page 4 - 20 GreensPro 1200...
  • Page 45 Drive Roller Assembly ........5-28 Transport Wheel ..........5-33 Transport Wheel Hub ........5-34 Lift Arm Assembly..........5-35 Lift Arm Catch Assembly ........5-37 Tow Bar Assembly..........5-39 Transmission Cover.......... 5-41 Seat Assembly..........5-42 GreensPro 1200 Page 5 - 1 Chassis...

  • Page 46: Specifications

    Transport Wheel Lug Nut Torque 80 ft-lb (108 N·m) Transport Wheel Tire Pressure 10 psi (0.65 bar) Axle Clamp Bolt Torque 35 ft-lb (47.5 N·m) Tow Bar Clamp Bolt Torque 35 ft-lb (47.5 N·m) Chassis Page 5 - 2 GreensPro 1200...

  • Page 47: General Information

    General Information Operator’s Manual The Operator’s Manual provides information regarding the operation, general maintenance, and maintenance intervals for your GreensPro machine. Refer to the Operator’s Manual for additional information when servicing the machine. GreensPro 1200 Page 5 - 3 Chassis...

  • Page 48: Steering Operation

    (1), and front steering head assembly (2). With the exception of the steering wheel and steering shaft, steering system components are attached to the bottom of the chassis shown in Figure 1. Chassis Page 5 - 4 GreensPro 1200...

  • Page 49: Traction Control Operation

    Traction control system components are attached to the bottom of the chassis shown in Figure 2. The motion pedals extend through the chassis, as does the link that attaches to the transmission control arm. GreensPro 1200 Page 5 - 5 Chassis...

  • Page 50: Adjustments

    5. Loosen jam nuts (1) on lifting bar (3) and turn lifting bar to achieve a distance of 26.77 in. (680 mm) between centers of ball joints (9). Tighten jam nuts (1). Repeat procedure for other side of machine. Chassis Page 5 - 6 GreensPro 1200...

  • Page 51: Lift Arm Catch Adjustment

    (3). 3. Make sure that lift arm catch properly engages lifting arm. It may be necessary to adjust linkage arm (2) length for proper operation. 4. After completing adjustments, tighten jam nuts (1). GreensPro 1200 Page 5 - 7 Chassis...

  • Page 52: Steering Linkage Adjustments

    Before attempting to loosen a hex nut for linkage disassembly, inspect the visible threads on the linkage rod to determine thread direction. Figure 8 Chassis Page 5 - 8 GreensPro 1200...
  • Page 53 (11) to ensure steering rollers are in alignment. Adjust steering head linkage arms (8) (refer to step 4) as necessary to achieve alignment. Figure 12 Incorrect Linkage Arm Adjustment 9. Position steering wheel (15) square with machine. Figure 10 GreensPro 1200 Page 5 - 9 Chassis...
  • Page 54 (4) as necessary to align steering heads. 11.Tighten jam nuts (5) on steering pivot rod (4), and tighten jam nuts (7) on steering head linkage arms (8). Chassis Page 5 - 10 GreensPro 1200...

  • Page 55: Motion Pedal Adjustment

    (3) is necessary. 4. To adjust linkage arm, remove transmission cover from machine to gain access to transmission linkage arm (see Transmission Cover in the Service and Repairs section of this chapter). GreensPro 1200 Page 5 - 11 Chassis...

  • Page 56: Service And Repairs

    3. Remove steering wheel bolt (2), lock washer (3), and flat washer (4). 4. Remove steering wheel (5) from upper steering shaft (7). 5. Remove steering shaft cover (6) from upper steering shaft (7). 6. Repair or replace parts as necessary. Chassis Page 5 - 12 GreensPro 1200...

  • Page 57: Steering Tower

    (8) securing upper bearing assembly (5) to steering column box (4). 5. Remove four cap screws (9), eight flat washers (10), and four lock nuts (11). Remove steering column box (4) from steering column (12). GreensPro 1200 Page 5 - 13 Chassis...
  • Page 58 12. Loosen cap screw (27) and remove universal joint (26) from steering pivot assembly (25). 13. Using a suitable lifting device, raise and support the machine to allow removal of the steering shaft. Chassis Page 5 - 14 GreensPro 1200...
  • Page 59 (36) on the steering pivot assembly (25). 16. Loosen two socket-head set screws (38). Remove upper flange (35), bearing (36), and lower flange (37) from steering pivot assembly (25). 17. Repair or replace parts as necessary. GreensPro 1200 Page 5 - 15 Chassis...
  • Page 60 (10). Make sure that beveled corners of pivot assembly are oriented toward front of machine. Figure 30 6. Install universal joint (17) on steering pivot assembly (2), and tighten cap screw (18). Chassis Page 5 - 16 GreensPro 1200...
  • Page 61 Figure 33 steering shaft (19). 11. Attach steering column (24) to roller chassis (10) 17. Lubricate universal joint (17) with grease. with four cap screws (25), flat washers (26), and lock nuts (27). GreensPro 1200 Page 5 - 17 Chassis...
  • Page 62 19. Install steering wheel (see Steering Wheel in this section). 20. Lower machine to the ground. 21. Check steering linkage adjustment and adjust if necessary (see Steering Linkage Adjustments in the Adjustments section of this chapter). Chassis Page 5 - 18 GreensPro 1200...

  • Page 63: Steering Control Assembly

    16. Hex nut (6 used) NOTE: When servicing steering linkage assemblies, steering disc, or steering heads, refer to Figure 37. Service procedures for these items are included on the following pages of this section. GreensPro 1200 Page 5 - 19 Chassis...
  • Page 64 4. Remove cap screw (2), plated washer (3), flat linkage disassembly, inspect the visible threads on the washer (4), and lock nut (5), and remove steering pivot linkage rod to determine thread direction. rod (1) from steering pivot assembly (6). Chassis Page 5 - 20 GreensPro 1200...
  • Page 65 (12). Figure 43 5. Install steering pivot rod (15) to steering disc assembly (1), and secure with cap screw (16), two plated washers (17), flat washer (14), and lock nut (13). GreensPro 1200 Page 5 - 21 Chassis...

  • Page 66: Steering Disc Assembly

    4. While supporting steering disc assembly (2) to prevent it from falling, remove lock nut (6) and plated washer (7). Then remove steering disc assembly (2) and steering spacer bushing (5) from chassis (8). Chassis Page 5 - 22 GreensPro 1200...
  • Page 67 Oilite bushings (4) into steering disc (6). ® Then insert pivot bushing (5) into installed Oilite bushings (4). 3. Install steering spacer bushing (7) and then steering disc assembly (6) onto cap screw. GreensPro 1200 Page 5 - 23 Chassis...

  • Page 68: Steering Head Assembly

    3. Remove lock nut (3) and flat washer (4), and disconnect tension spring (1) and anchor screw (2). Figure 54 6. Remove four lock nuts (11), four cap screws (12), and eight flat washers (13), and remove steering head assembly (8). Chassis Page 5 - 24 GreensPro 1200...
  • Page 69 9. Front steering head housing 10. Cap screw (4 used) 11. Long steering roller assembly 12. Short steering roller assembly 13. Lock nut (6 used) 14. Pivot shaft assembly 15. Cap screw (4 used) GreensPro 1200 Page 5 - 25 Chassis...
  • Page 70 (13). 4. Lower machine to the ground. Figure 57 2. Connect linkage arm (6) to steering head assembly (4) using cap screw (5), flat washer (8), spacer (9), and lock nut (7). Chassis Page 5 - 26 GreensPro 1200...

  • Page 71: Steering Rollers

    Do not overtighten lock nuts. 3. Remove and replace parts as necessary to repair the steering rollers. 6. Install steering rollers in steering head assembly. (See Steering Head Assembly in this section.) GreensPro 1200 Page 5 - 27 Chassis...

  • Page 72: Drive Roller Assembly

    5. Remove lock nut (1), two flat washers (2), cap screw (7), flat washer (8), and spacer (3), and remove drive Figure 62 chain tension assembly (6). 7. Remove two set screws (10). Chassis Page 5 - 28 GreensPro 1200...
  • Page 73 13. Remove drive roller assembly (15). 16 17 18 Figure 64 9. Remove key (14). 10. Support the drive roller assembly (15). 11. Remove two lock nuts (16), two cap screws (17), and four flat washers (18). GreensPro 1200 Page 5 - 29 Chassis...
  • Page 74 3. Install bearing assemblies (1), and tighten (but do flat washers (5), and remove roller axles (6 and 8). not overtighten) set screws (9). Bearing assemblies may need to be repositioned after drive roller assembly has been installed in machine. Chassis Page 5 - 30 GreensPro 1200...
  • Page 75 (5) to frame using two cap screws (1), two lock nuts (2), and four flat washers (3). 8 9 10 Figure 70 5. Install drive chain (17) and sprocket (14). Figure 68 GreensPro 1200 Page 5 - 31 Chassis...
  • Page 76 0.200 in. to 0.300 in. (5 to 8 mm) deflection at mid-span between the sprockets. 12. Install secure transmission cover (see Transmission Cover in this section). 13. Lower machine to the ground. Chassis Page 5 - 32 GreensPro 1200...

  • Page 77: Transport Wheel

    2. Tighten lug nuts in an alternating pattern to 80 ft-lb (108 N·m). 3. Adjust tire pressure to 10 psi (0.65 bar). Figure 72 2. Remove four lug nuts (1). 3. Remove transport wheel and tire assembly (2). GreensPro 1200 Page 5 - 33 Chassis...

  • Page 78: Transport Wheel Hub

    2. Remove transport wheels. (See Transport Wheel in this section.) 3. Remove cap screw (4), lock washer (5), and spacer (6). 4. Remove transport wheel hub (3). 5. Inspect bearings (1) and replace as necessary. Chassis Page 5 - 34 GreensPro 1200...

  • Page 79: Lift Arm Assembly

    Wheel Hub in this section.) Make sure engine is OFF. Remove spark plug wire 3. Release latch, lower the transport axle, and support from spark plug. the tow bar. GreensPro 1200 Page 5 - 35 Chassis...
  • Page 80 9. Install transport wheel hubs. (See Transport Wheel Hub in this section.) 10.Install transport wheels. (See Transport Wheel in this section.) Make sure that wheel lug nuts are properly tightened to 80 lb-ft (108 N·m). Chassis Page 5 - 36 GreensPro 1200...

  • Page 81: Lift Arm Catch Assembly

    3. Release wheel lock (15), and allow transport wheels Make sure engine is OFF. Remove spark plug wire to rest on blocks. from spark plug. GreensPro 1200 Page 5 - 37 Chassis...
  • Page 82 5. Make sure that wheel lock is engaged and remove blocks from under transport wheels. 6. Check operation of lift arm catch and adjust linkage arm assembly if required (see Lift Arm Catch Adjustment in the Adjustments section of this chapter). Chassis Page 5 - 38 GreensPro 1200...

  • Page 83: Tow Bar Assembly

    6. Lower the tow bar (12) to the ground. of the machine to prevent it from shifting. 3. Support the tow bar (12). 4. Remove nut (11), flat washer (10), cap screw (5), GreensPro 1200 Page 5 - 39 Chassis...
  • Page 84 (16), cap screw (19), flat washer (18), nut (11), and flat washer (10). 4. Connect lifting bar (3) to tow bar (12) using bushing (8), cap screw (5), flat washer (6), flat washer (10), and nut (11). Chassis Page 5 - 40 GreensPro 1200...

  • Page 85: Transmission Cover

    2. Remove lock nut (2), two flat washers (3), and cap screw (4). 3. Tilt seat and seat pan (1) forward. Figure 78 4. Remove cap screw (5) that secures transmission cover (6) to support frame. 5. Remove transmission cover (6) from machine. GreensPro 1200 Page 5 - 41 Chassis...

  • Page 86: Seat Assembly

    3. Disconnect hour meter wire harness (9) from seat machine. pan (1). 7. Replace or repair parts as necessary. 4. Remove four nuts (6), lock washers (7), and flat washers (8). Remove seat (5) from seat pan (1). Chassis Page 5 - 42 GreensPro 1200...
  • Page 87 Figure 84 NOTE: It may be necessary to move the slide portion of each adjuster rail to install cap screws. 2. Install seat adjuster rails (7) on seat (5) using four cap screws (6). GreensPro 1200 Page 5 - 43 Chassis...
  • Page 88 This page is intentionally blank. Chassis Page 5 - 44 GreensPro 1200...

Table of Contents