Table of Contents
Advertisement
APPENDIX E
F
14–1: NEW SETTINGS DIALOG BOX........................................................................................14-1
IGURE
F
14–2: CHANGE MODEL NUMBER ITEM DIALOG BOX............................................................14-1
IGURE
F
14–3: SELECT PROTECTION SCHEME DIALOG BOX ............................................................14-2
IGURE
F
14–4: CHANGE SETTINGS – PROTECTION DIALOG BOX .....................................................14-2
IGURE
F
14–5: CHANGE SETTING VALUE DIALOG BOX ......................................................................14-3
IGURE
F
14–6: SELECT CATEGORIES TO PRINT DIALOG BOX...........................................................14-3
IGURE
F
14–7: TOOL SETUP DIALOG BOX ............................................................................................14-4
IGURE
F
14–8: ABOUT ALPS-SET DIALOG BOX ....................................................................................14-4
IGURE
Figure D–1: SET KEYPAD MENU............................................................................................................ D-1
Figure D–2: ACT KEYPAD MENU ........................................................................................................... D-2
Figure D–3: INF KEYPAD MENU............................................................................................................. D-3
T
: 1–1 ORDER CODES FOR THE LPS-D.........................................................................................1-3
ABLE
T
: 1–2 LPS-D MEASUREMENT FUNCTIONS ..................................................................................1-5
ABLE
T
: 1–3 LPS-D DEFAULT CONTACT CONVERTER ASSIGNMENTS .............................................1-10
ABLE
T
: 1–4 LPS-D DEFAULT OUTPUT CONTACT ASSIGNMENTS.....................................................1-11
ABLE
T
: 2–1 NUM_TC SETTING (SINGLE PHASE MODELS) ..................................................................2-4
ABLE
T
: 2–2 NUM_TC SETTING (THREE PHASE MODELS) ...................................................................2-4
ABLE
T
: 2–3 SETTING FORMAT FOR NUM_MON ....................................................................................2-5
ABLE
T
: 2–4 OSCILLOGRAPHY CYCLES PER STORAGE EVENT .........................................................2-7
ABLE
T
: 2–5 PROPOSED SETTINGS FOR BLOCKING SCHEME ..........................................................2-25
ABLE
T
: 2–6 INDEX NUMBERS – CONTACT CONVERTER INPUT ASSIGNMENT...............................2-52
ABLE
T
: 2–7 INDEX NUMBERS –
ABLE
T
: 2–8 PROTECTION SETTINGS GUIDE .......................................................................................2-61
ABLE
T
: 2–9 GENERAL SETTINGS GUIDE .............................................................................................2-70
ABLE
T
: 2–10 PROTECTION SETTINGS DATA SHEET ..........................................................................2-73
ABLE
T
: 2–11 GENERAL SETTINGS DATA SHEET ................................................................................2-82
ABLE
T
: 3–1 JUMPER POSITION ...............................................................................................................3-7
ABLE
T
: 4–1 FACTORY DEFAULT COMMUNICATIONS PARAMETERS .................................................4-6
ABLE
T
: 4–2 DIGITAL OUTPUTS TEST CONNECTIONS ........................................................................4-10
ABLE
T
: 5–1 TIME-OUT VALUES WHILE REPEATING T8 ........................................................................5-6
ABLE
T
: 6–1 TEST CURRENT RANGES FOR PHASE-TO-GROUND REACH .......................................6-12
ABLE
T
: 6–2 TEST CURRENT RANGES FOR PHASE-TO-PHASE REACH ...........................................6-17
ABLE
T
: 8–1 PASSWORD ENCRYPTION KEY TABLE............................................................................8-25
ABLE
T
: 8–2 KEYPAD / DISPLAY INTERFACE ERROR MESSAGES.....................................................8-26
ABLE
T
: 8–3 HARDWARE SWITCH DESCRIPTIONS ..............................................................................8-28
ABLE
T
: 8–4 COMMAND SEQUENCE SENT BY ALPS-LINK TO MODEM .............................................8-29
ABLE
T
: 8–5 CONFIGURATION SETTINGS FOR THE MODEM CONNECTED TO THE RELAY...........8-30
ABLE
T
: 8–6 MODEM COMMANDS FOR COMMUNICATION BETWEEN RELAY AND PC ...................8-32
ABLE
T
: 9–1 COMPONENTS TESTED DURING START-UP TESTS ........................................................9-2
ABLE
T
: 9–2 RUN-TIME BACKGROUND SELF-TESTS.............................................................................9-2
ABLE
T
: 9–3 RUN-TIME FOREGROUND SELF-TESTS.............................................................................9-2
ABLE
T
: 9–4 SYSTEM STATUS ERROR MESSAGES...............................................................................9-3
ABLE
T
: 10–1 INPUT QUANTITIES...........................................................................................................10-3
ABLE
T
: 12–1 ASCII PROMPTS ................................................................................................................12-1
ABLE
T
: 12–2 OSCILLOGRAPHY DATA STRUCTURE ...........................................................................12-2
ABLE
T
: 12–3 ASCII COMMAND LIST ....................................................................................................12-2
ABLE
T
: 13–1 PICKUP DELAY TIMER TRUTH TABLE ............................................................................13-4
ABLE
T
: 13–2 CONTACT CONVERTER INPUT FLAGS ..........................................................................13-5
ABLE
T
: 13–3 CONFIGURABLE INPUTS .................................................................................................13-6
ABLE
T
: 13–4 SCHEME LOGIC INPUTS ..................................................................................................13-6
ABLE
T
: 13–5 SCHEME LOGIC AND RECLOSER OUTPUTS .................................................................13-7
ABLE
GE Power Management
,
, &
SCHEME
RECLOSER
PROGRAMMABLE LOGIC
LPS-D Line Protection System
E.1 TABLES AND FIGURES
E.1.2 LIST OF TABLES
......................................2-54
E
E-
3
Advertisement
Table of Contents
