Table of Contents
Advertisement
CASE ASSEMBLY ....................................................... 3-1
CC1 (General Setting 501) ........................................... 2-9
CC10 (General Setting 510) ......................................... 2-9
CC11 (General Setting 511) ......................................... 2-9
CC12 (General Setting 512) ......................................... 2-9
CC2 (General Setting 502) ........................................... 2-9
CC3 (General Setting 503) ........................................... 2-9
CC4 (General Setting 504) ........................................... 2-9
CC5 (General Setting 505) ........................................... 2-9
CC6 (General Setting 506) ........................................... 2-9
CC7 (General Setting 507) ........................................... 2-9
CC8 (General Setting 508) ........................................... 2-9
CC9 (General Setting 509) ........................................... 2-9
CHANGE BUS/STATION ID ....................................... 11-15
CHANNEL RELEASE TIME
definition ................................................................. 2-36
CHANNEL TEST ........................................................ 8-14
CIRCUIT BOARD LOCATIONS ..................................... 3-3
CIRCUIT BOARDS
bus card .................................................................... 3-3
communications interface .......................................... 3-9
DSP/ANI board ........................................................ 3-11
i960 CPU board ....................................................... 3-12
input .................................................................. 3-6, 3-7
local user interface logic ............................................ 3-6
locations ................................................................... 3-3
magnetics module ..................................................... 3-3
output ....................................................................... 3-6
power supply ........................................................... 3-10
warning ..................................................................... 3-6
CLOSE BREAKER ..................................................... 8-12
CLOSEANG (Protection Setting 1819) ................ 1-46, 2-45
CLOSE-ONTO-FAULT
see LINE PICKUP
CLR key ...................................................................... 8-2
COMMAND .................................................................. B-1
COMMUNICATIONS .................................................... 4-5
ASCII command list ................................................. 12-2
ASCII interface ................................................ 8-27, 12-1
ASCII prompts ......................................................... 12-1
connecting to local PC ............................................... 1-2
description ............................................. 1-22, 1-23, 12-1
DNP 3.0 .................................................................... C-1
general settings ......................................................... 2-6
interface board .......................................................... 3-9
LPS-D modem ......................................................... 8-30
modem commands ................................................... 8-29
modem connections/settings .................................... 8-29
null-modem connections .................................. 8-27, 8-31
parameters, factory default ........................................ 4-6
passwords ............................................................... 8-25
PC modem .............................................................. 8-29
recommended software packages ............................ 8-27
remote communications interface ............................. 8-28
serial ...................................................................... 1-22
troubleshooting ......................................................... A-1
COMMUNICATIONS INTERFACE ................................. 3-9
COMMUNICATIONS MODULE
block diagram ............................................................ 3-9
COMPENSATION FACTOR .......................................... 7-2
COMPORT1 (General Setting 201) ............................... 2-6
COMPORT2 (General Setting 202) ............................... 2-6
COMPORT3 (General Setting 203) ............................... 2-6
CONFGTRIP (Protection Setting 810) ......................... 2-31
CONFIGURABLE INPUT/OUTPUT
GE Power Management
INDEX
test connections .......................................................4-13
CONFIGURABLE INPUTS ...........................................1-10
CONFIGURABLE OUTPUTS .......................................1-11
CONFIGURATION ....................................................... 2-3
CONFOSC (Protection Setting 2026) .................. 1-18, 2-48
CONFTRIP (Protection Setting 2025) ..........................2-48
CONNECTING
to & logging out of device ....................................... 11-12
CONSTRUCTION ..................................................3-1, 3-6
CONTACT CONVERTER
calculation of settings ................................................ 2-9
default assignments ..................................................1-10
status ......................................................................8-21
CONTACT CONVERTERS
input flags ................................................................13-5
CONTACT RATINGS ................................................... 7-1
CONTINUOUS MONITOR ...........................................1-25
CONTRAST
adjusting ..................................................................8-18
CONTROL KEYS ......................................................... 8-2
COUNTERS ...............................................................13-4
CPU BOARD ..............................................................3-12
CTRATIO (Protection Setting 1407) .............................2-40
CURRENT SUPERVISION FUNCTION ......................... 7-2
CURRENT TRANSFORMER RATIO
setting .....................................................................2-40
CURRENT UNBALANCE DETECTION .........................1-18
CURSUPVISN SETTINGS CATEGORY ........................2-24
CURVES
extremely inverse curve ............................................2-51
inverse curve ...........................................................2-49
very inverse curve ....................................................2-50
CUSTOM PROGRAMMABILITY ...................................1-10
D
DATA ENTRY KEYS .................................................... 8-3
DATE/TIME
modifying .................................................................. 8-9
DBUSDLINE (Protection Setting 1838) ........................2-47
DBUSLLINE (Protection Setting 1837) .........................2-47
DEFAULT SETTINGS .................................................. 4-6
DEFECTIVE BOARDS
locating ..................................................................... 9-4
DEFTIMDELY (Protection Setting 616) ........................2-29
DELTAV (Protection Setting 1839) ...................... 1-46, 2-47
DELTAVBLK (Protection Setting 1840) ............... 1-46, 2-47
DEVICE PROFILE DOCUMENT (DNP 3.0) .................... C-2
DIGITAL OUTPUT
status ......................................................................8-22
test ..........................................................................8-15
DIGITAL OUTPUT / POWER SUPPLY
block diagram ...........................................................3-10
circuit board .............................................................3-10
DIGITAL OUTPUTS
test ........................................................................ 11-17
test connections .............................................. 4-10, 4-11
DIGITAL TO ANALOG INTERFACE
see SCADA DTA
DIMENSIONS .............................................................. 7-3
DIRECTIONAL COMPARISON BLOCKING SCHEME
see BLOCKING SCHEME
DISABLE OUTPUTS ...................................................8-10
LPS-D Line Protection System
iii
Advertisement
Table of Contents
