Settings For Iec60870-5-103 Communication; Settings For Iec61850 Communication; Setting For Modbus Communication - Toshiba GRE110 Instruction Manual

I E C 2 I 4
I E C 2 I 5
I E C 2 I 6
I E C 2 I 7
I E C 2 I 8
S M O D E
G O I N T
D E A D T
• Enter the relay address number on the "Modbus" line for Modbus or the "IEC" line for
IEC60870-5-103 and press the ENTER key.
• Enter IP address for IP1-1 to IP1-4, Subnet mask for SM1-1 to SM1-4, Default gateway for
GW1-1 to GW1-4, and SNTP server address for SI1-1 to SI2-4. two SNTP servers are
available.
Enter "0" or "1" on "SMODE" column to set the standard time synchronized mode for SNTP
server. Using low accuracy level of time server, synchronized compensation to maintain
synchronization accuracy may not be done automatically. Therefore enter "1", and
synchronized compensation is done forcibly. The default setting is "0".
Enter the IP address of the device for PG1-1 to PG2-4 if Ping response is checked.
IP address: ∗∗∗. ∗∗∗. ∗∗∗. ∗∗∗ (IP1-1. IP1-2. IP1-3. IP1-4) and (IP2-1. IP2-2. IP2-3. IP2-4)
SM1-1 to SM2-4, GW1-1 to GW2-4, SI1-1 to SI2-4: same as above.
• Press the
key.
ENTER
CAUTION:
Do not duplicate the relay address number.

Settings for IEC60870-5-103 communication

The lines "IECB1" to "IECB4" are used for auxiliary inputs for IEC103 events INF27 to
INF30 in Appendix N. Assign signals to the columns "IECB1" to "IECB4" by entering the
number corresponding to each signal referring to Appendix B.
The lines "IECGT" to "IECCT" are used for fault indications for IEC103 events INF68 to
INF71 in Appendix N. Assign signals to the columns "IECGT" to "IECCT" by entering the BO
numbers (1 to 8) corresponding to the binary output settings.
The lines "IECE1" to "IECE8" are used to assign the signals for user customization. Assign
signals to the columns "IECE1" to "IECE8" by entering the number corresponding to each
signal referring to Appendix B.
Note: Assign "0" to the column when the function is not used.
The lines "IECI1" to "IECI8" are used to assign the above signals from "IECE1" to "IECE8" to
each INF number. Enter the INF number to the columns "IECI1" to "IECI8".

Settings for IEC61850 communication

Enter the time on "GOINT" to set the maximum GOOSE message publishing term if GOOSE
message receive checked. Enter the time on "DEADT" to set the Keep Alive time of IEC 16850
communication.

Setting for Modbus communication

• Select "Switch" on the "Comms" screen to select the protocol and transmission speed (baud
rate), etc., for Modbus, IEC60870-5-103 and IEC61850.
0
0
This setting is displayed if submodel of
communication type is 2 and "RS485P" in
0
comms switch settimg is "IEC103".
0
0
This setting is displayed if submodel of
0
communication type is A-D.
1 s
This setting is displayed if submodel of
1 s
communication
"RS485P" in comms switch settimg
is "off".
 108 
6 F 2 T 0 1 7 2
type is A-D and