Siemens SINUMERIK 828D Operating Manual page 11
Hmi sl milling
Hide thumbs
Also See for SINUMERIK 828D:
- Function manual (1799 pages) ,
- Commissioning manual (1167 pages) ,
- Operating manual (926 pages)
Table of Contents
Advertisement
7.13
Changing program settings........................................................................................................204
7.14
Selection of the cycles via softkey .............................................................................................206
7.15
Calling technology functions ......................................................................................................210
7.15.1
Additional functions in the input screens ...................................................................................210
7.15.2
Checking input parameters ........................................................................................................210
7.15.3
Setting data for technological functions .....................................................................................211
7.15.4
Changing a cycle call .................................................................................................................211
7.16
Measuring cycle support ............................................................................................................212
8
Programming technological functions (cycles) ....................................................................................... 215
8.1
Drilling ........................................................................................................................................215
8.1.1
General ......................................................................................................................................215
8.1.2
Centering (CYCLE81) ................................................................................................................216
8.1.3
Drilling (CYCLE82).....................................................................................................................218
8.1.4
Reaming (CYCLE85) .................................................................................................................219
8.1.5
Deep-hole drilling (CYCLE83)....................................................................................................220
8.1.6
Boring (CYCLE86) .....................................................................................................................223
8.1.7
Tapping (CYCLE84, 840)...........................................................................................................225
8.1.8
Drill and thread milling (CYCLE78) ............................................................................................229
8.1.9
Positioning and position patterns ...............................................................................................232
8.1.10
Arbitrary positions (CYCLE802).................................................................................................233
8.1.11
Line position pattern (HOLES1) .................................................................................................234
8.1.12
Circle position pattern (HOLES2)...............................................................................................236
8.1.13
Repeating positions ...................................................................................................................237
8.2
Milling .........................................................................................................................................238
8.2.1
Face milling (CYCLE61) ............................................................................................................238
8.2.2
Rectangular pocket (POCKET3)................................................................................................240
8.2.3
Circular pocket (POCKET4).......................................................................................................244
8.2.4
Rectangular spigot (CYCLE76)..................................................................................................248
8.2.5
Circular spigot (CYCLE77).........................................................................................................250
8.2.6
Multi-edge (CYCLE79)...............................................................................................................252
8.2.7
Longitudinal groove (SLOT1).....................................................................................................254
8.2.8
Circumferential groove (SLOT2) ................................................................................................257
8.2.9
Open groove (CYCLE899).........................................................................................................260
8.2.10
Long hole (LONGHOLE) - only for G code programs................................................................266
8.2.11
Thread milling (CYCLE70) .........................................................................................................268
8.2.12
Engraving (CYCLE60) ...............................................................................................................272
8.3
Contour milling ...........................................................................................................................277
8.3.1
General ......................................................................................................................................277
8.3.2
Representation of the contour....................................................................................................277
8.3.3
Creating a new contour..............................................................................................................279
8.3.4
Creating contour elements.........................................................................................................281
8.3.5
Changing the contour.................................................................................................................285
8.3.6
Contour call (CYCLE62) - only for G code program ..................................................................286
8.3.7
Path milling (CYCLE72) .............................................................................................................287
8.3.8
Contour pocket/contour spigot (CYCLE63/64) ..........................................................................290
8.3.9
Predrilling contour pocket (CYCLE64).......................................................................................291
8.3.10
Milling contour pocket (CYCLE63).............................................................................................294
8.3.11
Residual material contour pocket (CYCLE63) ...........................................................................296
8.3.12
Milling contour spigot (CYCLE63)..............................................................................................298
8.3.13
Residual material contour spigot (CYCLE63) ............................................................................300
HMI sl Milling
Operating Manual, 06/2009, 6FC5398-7CP20-0BA0
Table of contents
11
Advertisement
Table of Contents
